background image

Setup

4.2 Printing from the Micro SD Card:

1. 

    Insert the included SD card into the slot on the side of the Control Box, ensuring that

        the metal contacts are facing upwards

2.

     Navigate to and select 

SD Card > Print > Print File

3.  

   Navigate to your desired GCODE File, then press the Dial to commence printing

        Your WANHAO 3D Printer will now heat up the Extruder and Heated Print Bed before 
        printing your 3D object

NOTE:

 If pressing print shows no files, chances are the SD Card has not been mounted. Remount your 

SD Card into the side of your Control Box

NOTE:

 If Extruder temperature is set at 0°C after attempting to print a file, the imported GCODE may

have some compatibility issues with the printer. Manually change the Extruder temperature using

Extruder > Temp 1 

or

 Quick Settings > Preheat PLA 

or 

ABS

 depending on material used

5. Removing 3D Objects from the Bed

When the WANHAO 3D Printer has completed printing your 3D printed object, it’s time to

remove the object from the bed.

1. 

    Wait until the Extruder and Heated Print Bed have cooled down to room temperature. This

        will allow the plastic to contract, making it easier to remove

2.

     Using the Scraper, carefully ‘wedge’ under one of the edges of the 3D object. Take care 

        tokeep  the Scraper flat with the bed, as to not cause damage to the Print Mat

3.

     As one edge begins to lift, gently manoeuvre the Scraper forward to continue to ‘wedge’

        between the 3D object and the Heated Print Bed

4.  

   Once the part has fully separated from the bed, it is safe to remove

        

NOTE:

 Never scrape towards your body, or injury could occur

NOTE:

 Removing a 3D object, particularly one with a large surface size, can be a long process. 

Never  rush when removing a 3D printed object

TIP: 

If you are persistently having trouble removing 3D printed objects, try the following:

•     Use a layer of blue masking tape (designed to not leave behind residue) on the Heated Print

       Bed. Be sure to remove and replace after each print

•     Check if the printing mat is damaged and replace if needed

       Replacement mats can be purchased at 

id.aliexpress.com/store/120824

30

AFTER SALES SUPPORT

86-571-23290996

[email protected]

Model : Duplicator 9

Содержание DUPLICATOR 9



























































Отзывы: