D1WWTD02E
9
Service Manual
DPC130X
___________________________________________________________________________________
General specifications
Working conditions
This catalogue shows technical specifications and diagrams measured with mineral oil of 46 mm
2
/s -
46 cSt
viscosity at 40°C -
104°F
temperature.
Nominal flow rating
(open center circuit)
on inlet port with compensator
@ stand-by (margin pressure)
150 l/min -
39.6 US gpm
@ 9 bar -
131 psi
on working ports with compensator
@ stand-by (margin pressure)
100 l/min -
26.4 US gpm
@ 7 bar -
102 psi
on working ports without compensator
@ stand-by (margin pressure)
130 l/min -
34.3 US gpm
@ 9 bar -
131 psi
Max. pressure
P
inlet port
315 bar (
1
) -
4500 psi
(
1
)
A
and
B
working ports
315 bar (
1
) -
4500 psi
(
1
)
Back pressure (max.)
on
T
outlet port
25 bar -
363 psi
on
L
drain port
2.5 bar -
36 psi
Standard internal
leakage A(B)->T
∆p=100 bar -
1450 psi
16 cm
3
/min -
0.98 in
3
/min
with port valves, ∆p=100 bar -
1450 psi
21 cm
3
/min -
1.28 in
3
/min
Fluid
Mineral oil
Fluid temperature range
with seals NBR (BUNA-N)
from -20
°
C to 80
°
C -
from -4°F to 176°F
with seals FPM (VITON)
from -20
°
C to 80
°
C -
from -4°F to 176°F
Viscosity
operating range
from 15 to 75 mm
2
/s -
from 15 to 75 cSt
min.
12 mm
2
/s -
12 cSt
max.
400 mm
2
/s -
400 cSt
Contamination level
max.
-/18/15 - ISO 4406 -
NAS 1638 class 9
Environmental
temperature for working conditions
from -20
°
C to 60
°
C (
2
) -
from -4°F to 140°F
(
2
)
Environmental
pressure for working conditions
from +0.8 to + 1.1 bar -
from +11.6 to 16 psi
NOTES: (
1
) According to NFPA T 2.6.1., fatigue rating verified for 1 million cycles on 6 sample valves with test Pressure = 1.23 x Max. pressure
indicated - (
2
) DPC130X can operate with gases with an ignition temperature above 135°C -
275°F
and powders with an ignition temperature
above 130°C -
266°F
.
REFERENCE STANDARD
BSP
UN-UNF
THREAD
ACCORDING TO
ISO 228/1
ISO 263
BS 2779
ANSI B1.1 unified
CAVITY
DIMENSION
ACCORDING TO
ISO
1179
11926
SAE
J1926
DIN 3852-2, X or Y shape
PORTS
BSP
UN-UNF
P
inlet
G 3/4
1 1/16-12 (SAE 12)
A
and
B
ports
G 1/2
7/8-14 (SAE10)
T
outlet
G 3/4
1 1/16-12 (SAE 12)
LS
Load Sensing
G 1/4
9/16-18 (SAE 6)
V1
pilot
G 1/4
9/16-18 (SAE 6)
V2
pilot
depends on inlet section type:
see pages from 14 to 17 (
5
)
L
drain
G 1/4
7/16-20 (SAE 4)
M
pressure gauge
G 1/4
9/16-18 (SAE 6)
Hydraulic control ports
G 1/4
9/16-18 (SAE 6)
NOTES (
5
): ATTENTION! V2 pilot port requires dedicated
joints; please see Inlet section pages.
NOTES (
3
): Standard pressure series - (
4
): For pressure up to 350 bar
(
5100 psi
)
Standard thread
