WALTCO HDC-33 страница 2 Скачать руководство пользователя

Страница: 2 / 55

Table of Contents

Introduction

......................................................................................................................................

Safety Information

...........................................................................................................................

Liftgate Terminology

.......................................................................................................................

Basic Mounting Requirements

......................................................................................................

Liftgate Installation

.........................................................................................................................

Electrical Installation

......................................................................................................................

Electrical Schematics

....................................................................................................................

Electrical Trouble Shooting

..........................................................................................................

Battery Connection…

....................................................................................................................

Fill Reservoir

...................................................................................................................................

Platform Install

................................................................................................................................

Up-Stop

...........................................................................................................................................

Platform Tilt/Cylinder Adjustment

................................................................................................

Bumper

............................................................................................................................................

Swing Door Applications

...............................................................................................................

Check Operation

............................................................................................................................

Placement of Decals

.....................................................................................................................

Lubrication Instructions

.................................................................................................................

Final Inspection

..............................................................................................................................

Optional Kit Instructions:
Aux Battery Kit (Truck)

..................................................................................................................

Kit #80001066
Aux Battery Kit (Trailer)
Kit #80001069
Full Door Seal Kit

...........................................................................................................................

Kit #80000573
Cycle Counter Kit

...........................................................................................................................

How to Order Parts

........................................................................................................................

Improper installation of this liftgate could result in severe personal injury or
death.

Read and understand the contents of these instructions before proceeding.

When installed, this liftgate must not alter or prevent vehicle compliance to any
existing state or federal standards.

Each chassis manufacturer’s recommendations should be consulted for
compliance.

Содержание HDC-33
























































Результаты поиска

Содержание HDC-33

Отзывы:

Похожие инструкции для HDC-33

Бренды по названию

Популярные бренды

WALTCO HDC-33, Руководство по установке

Результаты поиска

Содержание HDC-33

Отзывы:

Похожие инструкции для HDC-33

Бренды по названию

Популярные бренды