Wallenstein HUF12000E Скачать руководство пользователя страница 25

Страница: 25 / 37

OPERATING SAFETY

• Store the unit in an area away from human

activity.

• Do not permit children to play on or around

the stored machine.

• Store the unit in a dry, level area. Support the

frame with planks if required.

.8 STORAGE

After the season's use or when the machine will not

be used for a period of time, completely inspect all

major systems of the Portable Generator. Replace

or repair any worn or damaged components to pre-

vent any unnecessary down time at the beginning

of the next season.

Follow this procedure before storing:

1. Remove all plugs or electrical loads from the

electrical panel.

2. Thoroughly clean the machine with a damp cloth

to remove all dirt, mud or debris.

3. Inspect all rotating parts for entangled material.

Remove all entangled material.

4. Turn fuel valve off.

5. Touch up all paint nicks and scratches to prevent

rusting.

6. Remove ignition key and store in a secure

place.

7. Remove the battery and store it in a cool, dry

area on wooden blocks or a wooden pallet.

Charge it monthly to maintain an adequate

charge.

8. It is best to store the machine inside. If that is

not possible, cover with a waterproof tarpaulin

and tie down securely.

9. Store in an area away from human activity.

10. Do not allow children to play around the stored

unit.

.8. PLACING IN STORAGE

When removing this machine from storage, follow

this procedure:

1. Remove the tarpaulin if covered.

2. Install and connect the battery.

3. Bring the ignition key.

4. Review and follow the pre-operation checklist.

.8.2 REMOVING FROM STORAGE

IMPORTANT

If the machine has been stored for more

than 6 months, warm the engine by

running it for 2-3 minutes and drain the

oil. Change the oil while the oil is warm

to remove any condensation. Refer to

Maintenance section.

Fig. STORED (Typical)

Содержание HUF12000E






































Результаты поиска

Содержание HUF12000E

Отзывы:

Похожие инструкции для HUF12000E

Бренды по названию

Популярные бренды

Wallenstein HUF12000E, Руководство пользователя

Результаты поиска

Содержание HUF12000E

Отзывы:

Похожие инструкции для HUF12000E

Бренды по названию

Популярные бренды