Wallenstein BX36S Скачать руководство пользователя страница 18

Страница: 18 / 52

Familiarization

BX36S

3PH Self-feed Chipper

7.2 Replace Damaged Safety Signs

Keep safety signs clean and legible at all times.

Replace safety signs that are missing or have

become illegible.

Parts that were replaced with a safety label on

them must also have the safety sign replaced.

Replacement safety signs are available from your

authorized Distributor or Dealer Parts Department

or the factory.

7.3 How to Install Safety Signs

Be sure that the installation area is clean and dry.

Be sure temperature is above 50 °F (10 °C).

Determine exact position before removing the

backing paper.

Remove the smallest portion of the split backing

paper.

Align the sign over the specified area and carefully

press the small portion with the exposed sticky

backing in place.

Slowly peel back the remaining paper and carefully

smooth the remaining portion of the sign in place.

Small air pockets can be pierced with a pin and

smoothed out using the piece of sign backing

paper.

8. Familiarization

8.1 To the New Operator or Owner

Wallenstein BX Series Wood Chippers are designed to

chip and chop scrap lumber, small trees, brush, limbs

and other wood debris. The chipped material is fine

enough to be composted or used in a variety of ways.

It is the responsibility of the owner or operator to

read this manual and to train all other operators

before they start working with the machine. Follow

all safety instructions exactly. Safety is everyone's

business. By following recommended procedures,

a safe working environment is provided for the

operator, bystanders and the area around the work

site. Untrained operators are not qualified to use

the machine.

Many features incorporated into this machine are the

result of suggestions made by customers like you.

Read this manual carefully to learn how to use the

chipper safely and how to set it to provide maximum

field efficiency. By following these instructions in

conjunction with a good maintenance program, your

BX Wood Chipper will provide many years of trouble-

free service.

IMPORTANT! Make sure all operators

understand how to place the machine in a Safe

Condition before working with this machine. See

page 9.

8.2 Operator Orientation

IMPORTANT! The directions for left-hand,

right-hand, backward and forward mentioned

throughout this manual are determined when

facing the chipper chute.

Содержание BX36S





















































Результаты поиска

Содержание BX36S

Отзывы:

Бренды по названию

Популярные бренды

Wallenstein BX36S, Руководство по эксплуатации

Результаты поиска

Содержание BX36S

Отзывы:

Бренды по названию

Популярные бренды