Walker Walker Mowers Скачать руководство пользователя страница 20

Страница: 20 / 76

Safety Instructions

SAFETY, CONTROL, AND INSTRUCTION DECALS

Safety, Control, and Instruction Decals are installed on the machine;

if any are missing, illegible, or damaged, a replacement should be ordered and installed before

putting the machine into operation. The Decal Part Number is listed below and in the Parts Manual.

Location: Flex Coupler Guard in Front of Engine
Part Number: 8600-2

8600-2

1. Warning – entanglement and cutting/dismem-

berment hazards
•

Keep away from rotating shafts, belts, and

other components.

Location: Right Fender
Part Number: 2802-2

Location: Underside of Rear Body
Part Number: 2107-4

1. Ground drive belt routing
2. PTO clutch belt routing

TIGHTEN UNTIL CONTACT WITH FRAME

DO NOT OVERTIGHTEN

THEN LOOSEN ONE TURN

Location: Chassis Member Behind Transaxles
Part Number: 2351-8

1. Forward Speed Control

•

Move lever forward to increase speed; back

to stop.

2. Body Tilt Latch

•

Raise lever to release.

•

Lift at back of body to raise.

3. Blade Clutch Lever

•

Move lever forward to engage PTO clutch;

back to disengage.

Содержание Walker Mowers













































































Результаты поиска

Содержание Walker Mowers

Отзывы:

Похожие инструкции для Walker Mowers

Бренды по названию

Популярные бренды

Walker Walker Mowers, Руководство оператора

Результаты поиска

Содержание Walker Mowers

Отзывы:

Похожие инструкции для Walker Mowers

Бренды по названию

Популярные бренды