Walker Walker Mowers Скачать руководство пользователя страница 19

Страница: 19 / 76

Safety Instructions

SAFETY, CONTROL, AND INSTRUCTION DECALS

Safety, Control, and Instruction Decals are installed on the machine;

if any are missing, illegible, or damaged, a replacement should be ordered and installed before

putting the machine into operation. The Decal Part Number is listed below and in the Parts Manual.

Location: Deck Housing Under Footrest
Part Number: 2749-3

1. Deck drive belt routing

1. Fuel tank selector/fuel shut-off valve.

Location: Adjacent to Left Fuel Tank
Part Number: 2010-4

5848-2

Location: Deck Discharge Shield (DSD60)
Part Number: 5848-2

1. Warning – thrown object hazard

•

Always keep the discharge shield in the low-

est position when operating.
•

Do not remove the discharge shield.

Location: Top of Deck Housing
Part Number: 8653-1

1. Warning – secure deck with straps and engage

parking brake before transporting or trailering
with deck tilted up.

Location: Deck Height Adjuster
Part Number: 2748-1

5.0

127

4.5

114

4.75

121

4.25

108

4.0

102

3.75

3.5

3.25

3.0

2.75

2.5

2.25

2.0

1.75

1.5

1.0

1.25

inch

2748-1

1. Move pin to desired height of cut.

Location: Engine Shroud
Part Number: 5855

Содержание Walker Mowers













































































Результаты поиска

Содержание Walker Mowers

Отзывы:

Похожие инструкции для Walker Mowers

Бренды по названию

Популярные бренды

Walker Walker Mowers, Руководство оператора

Результаты поиска

Содержание Walker Mowers

Отзывы:

Похожие инструкции для Walker Mowers

Бренды по названию

Популярные бренды