Walker Walker Mowers Скачать руководство пользователя страница 25

Страница: 25 / 76

Assembly Instructions

Mower Deck Installation on Tractor

Deck Installation

1. Lightly grease each deck support arm (2) on the

tractor. Refer to

Mower Deck Installation

photo

for location of deck support arm.

Deck Support

Arms

Mower Deck Installation

2. Engage the LH deck carrier frame tube socket

first on the tractor support arms and then the RH

tube socket. Slide the deck onto the support
arms and install lynch pins to secure deck.

3. Retract the spring-loaded quick disconnect ring

on the PTO Coupler and insert the Coupler Instal-
lation Tool (provided in Owner’s Packet) as
shown in the photo below.

NOTE:

The Coupler Installation Tool is provided

for convenience, but is not required for installa-
tion.

Retract Coupler Ring

Coupler

Installation Tool

Retract Spring-Loaded
Quick Disconnect Ring

PTO Coupler

Tube

PTO Coupler Installation Tool

4. Reaching under the tractor, slide the PTO cou-

pler tube onto the deck drive shaft (align arrow
decals), then install the coupler quick discon-
nect onto the tractor PTO drive shaft.

5. Remove Installation Tool from quick disconnect

ring and make sure the ring has “snapped” se-
curely on the spline shaft.

Installation Tool Removal

IMPORTANT:

DO NOT

operate tractor with

Coupler Installation Tool installed.

Содержание Walker Mowers













































































Результаты поиска

Содержание Walker Mowers

Отзывы:

Похожие инструкции для Walker Mowers

Бренды по названию

Популярные бренды

Walker Walker Mowers, Руководство оператора

Результаты поиска

Содержание Walker Mowers

Отзывы:

Похожие инструкции для Walker Mowers

Бренды по названию

Популярные бренды