OVER FENDER & REAR DOOR PANEL
Recommend to paint protective coating on the back side of WALD Over Fender.
2013/04
【
BEFORE PAINTING
】
１） Remove OEM over fender according to the Mercedes-Benz service manual.
２） Temporarily install WALD Over Fender to the body.
※ See how to process on WALD Rear Over Fender when installing WALD Door Panel
according to the picture.
３） Mark the installation positions for OEM tapping screws on the attached inner panels
to fix on WALD Rear Over Fenders.
４） Make holes on the attached inner panels according to the marked positions.
５） Paint WALD Over Fenders according to the picture.
【AFTER PAINTING】
６） Use caulking glue to fix the attached meshes from the rear.
７） Fix the attached inner panels on WALD Rear Over Fenders.
８） Install WALD Over Fenders to the body and tighten OEM bolts and tapping screws.
※ MORE THAN 2 TECHNICIANS ARE NECESSARY IN THIS WORK.
DURING ALL THE INSTALLATION PROCESS, PLEASE BE CAREFUL NOT TO DAMAGE THE BODY.
※ ADJUST ALL THE DETAILS OF OUR PRODUCTS TO FIT ON A CAR PERFECTLY.
ADD: 10-13 KYOGUCHI-CHO, TAKATSUKI, OSAKA, JAPAN
WALD. INTERNATIONAL
ZIP: 569-0072 TEL: (81)-72-673-3000 FAX: (81)-72-673-3003
ATTENTION
Use OEM tapping screws for
WALD Front and Rear
Over Fenders.
OEM BOLTS
OEM NUTS
OEM
OVER FENDER
MOLDING
OEM
OVER FENDER
MOLDING
WALD DOOR PANEL & FENDER PANEL
Mercedes Benz
G-class
(W463)
INSTALLATION MANUAL
Completely degrease and paint primer on all
the installation positions to enhance the viscidity
of double sided tape.
Use dryer to warm double sided tape to enhance
the viscidity in low temperature.
Keep the car in a dry condition more than
24 hours after gluing.
Do not wash the car during this time.
THANK YOU FOR PURCHASING. THIS IS THE INSTALLATION MANUAL OF WALD OVER FENDER AND REAR DOOR PANEL FOR MERCEDES-BENZ W463 G-CLASS.
PLEASE READ THIS MANUAL CAREFULLY BEFORE THE INSTALLATION.
※ NO RETURNS CAN BE ACCEPTED BECAUSE OF IMPROPER INSTALLATION OR PAINTING.
※ CHECK THE FITMENT, AND ADJUST ALL THE DETAILS BEFORE PAINTING.
Please purchase double sided tape,
primer and caulking glue at
auto accessory shop or hardware store.
Use caulking glue
to fill the gap
between the product
and the body.
※ PLEASE BE AWARE OF:
■ You may lose the warranty and all the services from the car maker, because of replacing OEM parts.
■ Reduced road clearance may cause inconvenience in using parking curbs and garage jack.
■ FRP, ABS and PPE products are slightly weaker than OEM parts in crashes.
■ The product may not match the body and OEM color perfectly.
■ We assume no responsibility for any damage resulting from improper installation, painting,
modification and any cut wound in unsealing.
■ Contact the car dealer when you have any question in removing OEM parts.
■ During all the installation process, use parking brake and stop the engine completely.
■ Use rasps or sandpapers to fit the products to the body if there is an individual difference.
■ The product is made of FRP. Handle with care. Do not give the excessive force.
Gradually fix the bolts and nuts by checking the fitment and balance of the installation.
■ Check the fitment, and adjust all the details of the fitment steady and proper.
Please check the fitment and all the details regularly, fix the bolts and nuts as necessary.
■ The instruction of painting is just our recommendation, please paint it as you like.
PARTS
QUANTITIES
1 SET
1 SET
1 SET
1 SET
1 SET
OVER FENDER
INNER PANELS
MESHES
REAR DOOR PANELS
FENDER PANELS
OVER FENDER
REAR DOOR PANEL
ATTENTION
ATTACHED MESH
MATTE BLACK
■HOW TO INSTALL THE
ATTACHED MESHES (STEP 6)
Use pins and caulking glue to install the
attached meshes to
WALD Rear Bumper from the rear.
※Paint the inside of the ducts and pins in black.
■WALD SHOWCAR IS PAINTED
LIKE THE PICTURE (STEP 5)
Make clear coating for the carbon parts
of WALD Front Bumper.
WALD REAR OVER FENDER
Cut here.
■HOW TO PROCESS WALD REAR OVER FENDER (STEP 2)
Need to cut WALD Rear Over Fender and
OEM Door Molding when installing
WALD Rear Door Panels.
Be careful to adjust the location and
balance based on a car.
ATTACHED INNER PANE
■HOW TO INSTALL THE
ATTACHED INNER PANELS (STEP 2)
Use OEM tapping screws to connect
the attached inner panels with
OEM inner liners.
※Adjust the shape and
location based on OEM inner liners.
MBMANUALS.COM
