REAR BUMPER
2013/04
【
BEFORE PAINTING
】
１） Remove OEM rear bumper according to the Mercedes-Benz service manual.
２） Replace OEM brackets to WALD Rear Bumper.
３） Temporarily fix WALD Rear Bumper to the body with all the necessary parts.
※ Adjust the details of WALD Rear Bumper to fit the body by rasps or sandpapers.
４） Cut OEM mud-guard according to the shape of WALD Rear Bumper.
５） Paint WALD Rear Bumper according to the picture.
【AFTER PAINTING】
６） Use caulking glue to fix the attached meshes from the rear.
７） Fix OEM mud-guard to WALD Rear Bumper.
※ Use caulking glue if the OEM tapping screws are not available.
８） Temporarily install WALD Rear Bumper to the body.
９） Check all the details of the fitment, then tighten all the OEM bolts and the attached bolts.
Recommend to paint protective coating
on the back side of WALD Over Fender.
※ MORE THAN 2 TECHNICIANS ARE NECESSARY IN THIS WORK.
DURING ALL THE INSTALLATION PROCESS, PLEASE BE CAREFUL NOT TO DAMAGE THE BODY.
※ ADJUST ALL THE DETAILS OF OUR PRODUCTS TO FIT ON A CAR PERFECTLY.
ADD: 10-13 KYOGUCHI-CHO, TAKATSUKI, OSAKA, JAPAN
WALD. INTERNATIONAL
ZIP: 569-0072 TEL: (81)-72-673-3000 FAX: (81)-72-673-3003
ATTENTION
OEM BACK-UP LIGHT
(Replace from OEM Rear Bumper)
OEM BOLT
※Fix OEM bolts through the
replaced brackets on
WALD Rear Bumper.
LICENSE PLATE LIGHT
(Replace from OEM Rear Bumper)
OEM REAR FOG LAMP
(Replace from OEM Rear Bumper)
ATTACHED BOLTS (M6 x 12) &
RUBBER WASHERS
※Fix WALD Over Fender and
Rear Bumper together.
ATTACHED RUBBER MOLDING
Mercedes Benz
G-class
(W463)
INSTALLATION MANUAL
Completely degrease and paint primer on all
the installation positions to enhance the viscidity
of double sided tape.
Use dryer to warm double sided tape to enhance
the viscidity in low temperature.
Keep the car in a dry condition more than
24 hours after gluing.
Do not wash the car during this time.
THANK YOU FOR PURCHASING. THIS IS THE INSTALLATION MANUAL OF WALD REAR BUMPER FOR MERCEDES-BENZ W463 G-CLASS.
PLEASE READ THIS MANUAL CAREFULLY BEFORE THE INSTALLATION.
※ NO RETURNS CAN BE ACCEPTED BECAUSE OF IMPROPER INSTALLATION OR PAINTING.
※ CHECK THE FITMENT, AND ADJUST ALL THE DETAILS BEFORE PAINTING.
Please purchase double sided tape,
primer and caulking glue at
auto accessory shop or hardware store.
Use caulking glue
to fill the gap
between the product
and the body.
※ PLEASE BE AWARE OF:
■ You may lose the warranty and all the services from the car maker, because of replacing OEM parts.
■ Reduced road clearance may cause inconvenience in using parking curbs and garage jack.
■ FRP, ABS and PPE products are slightly weaker than OEM parts in crashes.
■ The product may not match the body and OEM color perfectly.
■ We assume no responsibility for any damage resulting from improper installation, painting,
modification and any cut wound in unsealing.
■ Contact the car dealer when you have any question in removing OEM parts.
■ During all the installation process, use parking brake and stop the engine completely.
■ Use rasps or sandpapers to fit the products to the body if there is an individual difference.
■ The product is made of FRP. Handle with care. Do not give the excessive force.
Gradually fix the bolts and nuts by checking the fitment and balance of the installation.
■ Check the fitment, and adjust all the details of the fitment steady and proper.
Please check the fitment and all the details regularly, fix the bolts and nuts as necessary.
■ The instruction of painting is just our recommendation, please paint it as you like.
PARTS
QUANTITIES
1
1 SET
1 SET
6
4
6
REAR BUMPER
MESHES
RUBBER MOLDING
BOLTS (M6 x 12)
NUTS (M8)
RUBBER WASHERS
REAR BUMPER
ATTENTION
■HOW TO INSTALL THE
ATTACHED MESHES (STEP 6)
Use pins and caulking glue to install the
attached meshes to WALD Rear Bumper
from the rear.
※Paint the inside of the ducts and pins in black.
■WALD SHOWCAR IS PAINTED
LIKE THE PICTURE (STEP 5)
Make clear coating for the carbon parts
of WALD Front Bumper.
ATTACHED MESH
MATTE BLACK
ATTACHED NUT (M8)
OEM BOLT
OEM BRACKET
■HOW TO INSTALL OEM BRACKET (STEP 2)
Replace OEM brackets from OEM Rear Bumper,
and fix them on WALD Rear Bumper with OEM bolts
and attached Nuts (M8).
■HOW TO INSTALL
OEM MUD-GUARD (STEP 4)
Cut the part according to
WALD Rear Bumper.
Cut here
(About 8 cm)
OEM MUD-GUARD
MBMANUALS.COM
