BONNET
【BEFORE PAINTING】
１）Remove OEM bonnet according to the Mercedes-Benz
service manual.
２）Temporarily install WALD Bonnet to the body after
pre-fixing all the necessary parts.
※Adjust the details of WALD Bonnet to fit the body
by rasps or sandpapers.
３）Paint WALD Bonnet according to the picture.
【AFTER PAINTING】
４）Fix all the necessary parts to WALD Bonnet,
then install to the body.
５）Tighten OEM bolts, attached bolts and nuts after
checking the balance.
※
MORE THAN 2 TECHNICIANS ARE NECESSARY IN THIS WORK.
DURING ALL THE INSTALLATION PROCESS, PLEASE BE CAREFUL NOT TO DAMAGE THE BODY.
※ADJUST ALL THE DETAILS OF WALD PRODUCTS TO FIT ON THE BODY.
Mercedes Benz
G-class
(W463)
2013/04
Completely degrease and paint primer on all
the installation positions to enhance the viscidity
of double sided tape.
Use dryer to warm double sided tape to enhance
the viscidity in low temperature.
Keep the car in a dry condition more than
24 hours after gluing.
Do not wash the car during this time.
※ NO RETURNS CAN BE ACCEPTED BECAUSE OF IMPROPER INSTALLATION OR PAINTING.
※ CHECK THE FITMENT, AND ADJUST ALL THE DETAILS BEFORE PAINTING.
Please purchase double sided tape,
primer and caulking glue at
auto accessory shop or hardware store.
※ PLEASE BE AWARE OF:
■ You may lose the warranty and all the services from the car maker, because of replacing OEM parts.
■ Reduced road clearance may cause inconvenience in using parking curbs and garage jack.
■ FRP, ABS and PPE products are slightly weaker than OEM parts in crashes.
■ The product may not match the body and OEM color perfectly.
■ We assume no responsibility for any damage resulting from improper installation, painting,
modification and any cut wound in unsealing.
■ Contact the car dealer when you have any question in removing OEM parts.
■ During all the installation process, use parking brake and stop the engine completely.
■ Use rasps or sandpapers to fit the products to the body if there is an individual difference.
■ The product is made of FRP. Handle with care. Do not give the excessive force.
Gradually fix the bolts and nuts by checking the fitment and balance of the installation.
■ Check the fitment, and adjust all the details of the fitment steady and proper.
Please check the fitment and all the details regularly, fix the bolts and nuts as necessary.
■ The instruction of painting is just our recommendation, please paint it as you like.
ATTENTION
PARTS
QUANTITIES
BONNET
1
BONNET
BOLTS (M6 x 12)
2
1
NUTS (M8)
Use caulking glue
to fill the gap
between the product
and the body.
THANK YOU FOR PURCHASING. THIS IS THE INSTALLATION MANUAL OF WALD BONNET FOR MERCEDES-BENZ W463 G-CLASS.
INSTALLATION MANUAL
ADD: 10-13 KYOGUCHI-CHO, TAKATSUKI, OSAKA, JAPAN
WALD. INTERNATIONAL
ZIP: 569-0072 TEL: (81)-72-673-3000 FAX: (81)-72-673-3003
ATTENTION
RUBBER CUSHIONS
(Replace from OEM bonnet)
ATTACHED BOLTS
(M6 x 12)
OEM BOLTS
OEM BOLTS
HINGES (Replace from OEM bonnet)
BONNET RELEASE LEVER
(Replace from OEM bonnet)
ATTACHED NUT
(M8)
OEM LEAF SPRINGS
OEM BONNET INSULATION
Use heat-resistant glue to fix
on OEM bonnet.
■HOW TO REPLACE OEM WASHER PANEL
(STEP 2)
Replace OEM washer panel to WALD Bonnet.
Use OEM Clips to fix on WALD Bonnet
OEM BONNET GRILLE
※WALD SHOWCAR IS PAINTED
LIKE THE PICTURE (STEP 3)
Make clear coating for the carbon
parts of WALD Front Bumper.
MATTE BLACK
MBMANUALS.COM
