LED LAMP KIT
2013/04
Mercedes Benz
G-class
(W463)
THANK YOU FOR PURCHASING. THIS IS THE INSTALLATION MANUAL OF WALD BONNET FOR MERCEDES-BENZ W463 G-CLASS.
INSTALLATION MANUAL
【BEFORE PAINTING】
１）Temporarily fix the attached LED lamps according
to the guide-line wallls on WALD Front Bumper.
※Adjust the details of WALD Front Bumper to fit the
attached LED lamps by rasps or sandpapers.
２）Prepare to connect the attached LED lamps.
※Insulate any spare harness.
３）Paint WALD Bonnet according to the picture.
【AFTER PAINTING】
４）Completely degrease the installation positions,
then put the atached LED lamps according
to the guide-line walls on WALD Front Bumper.
５）Use caulking glue to fix the attached LED lamps
after checking the angle and location.
６）Leave them till completely fixed.
７）Install WALD Front Bumper to the body
after connecting the harness.
ADD: 10-13 KYOGUCHI-CHO, TAKATSUKI, OSAKA, JAPAN
WALD. INTERNATIONAL
ZIP: 569-0072 TEL: (81)-72-673-3000 FAX: (81)-72-673-3003
※
REMOVE THE BATTERY BEFORE ALL THE WIRING WORKS.
※
MAKE SURE OEM FOG LAMPS ARE FINE TO WORK BEFORE THE INSTALLATION.
ATTENTION
ATTACHED BOLTS (M5 x 15)
ATTACHED BOLTS (M5 x 15)
LED LAMP KIT
※Insulate OEM fog lamp harness.
[ AS FOG LAMP ]
FOG LAMP
⊕
FOG LAMP
⊖
NOT CONNECTING
RELAY
BOX
LED LAMP
LED LAMP
[ AS DAYLIGHT ]
＝ WIRING DIAGRAM ＝
CAR SID
E
IGNITION
GROUNDING WIRE
POSITION LAMP
RELAY
BOX
■ Please purchase relay harness with remote controller kit
to turn on the daylights or fog lamps separately.
RED
BLACK
BLUE
RED
BLACK
BLUE
■HOW TO INSTALL THE ATTACHED
LED LAMPS (STEP 1, 3)
LED LAMP
LED
ATTACHMENT
Fix the attached LED lamps
according to the picture.
LED LAMP
(Face of the lens)
GUIDE-LINE
WALL
Completely degrease and paint primer on all
the installation positions to enhance the viscidity
of double sided tape.
Use dryer to warm double sided tape to enhance
the viscidity in low temperature.
Keep the car in a dry condition more than
24 hours after gluing.
Do not wash the car during this time.
※ NO RETURNS CAN BE ACCEPTED BECAUSE OF IMPROPER INSTALLATION OR PAINTING.
※ CHECK THE FITMENT, AND ADJUST ALL THE DETAILS BEFORE PAINTING.
Please purchase double sided tape,
primer and caulking glue at
auto accessory shop or hardware store.
※ PLEASE BE AWARE OF:
■ You may lose the warranty and all the services from the car maker, because of replacing OEM parts.
■ Reduced road clearance may cause inconvenience in using parking curbs and garage jack.
■ FRP, ABS and PPE products are slightly weaker than OEM parts in crashes.
■ The product may not match the body and OEM color perfectly.
■ We assume no responsibility for any damage resulting from improper installation, painting,
modification and any cut wound in unsealing.
■ Contact the car dealer when you have any question in removing OEM parts.
■ During all the installation process, use parking brake and stop the engine completely.
■ Use rasps or sandpapers to fit the products to the body if there is an individual difference.
■ The product is made of FRP. Handle with care. Do not give the excessive force.
Gradually fix the bolts and nuts by checking the fitment and balance of the installation.
■ Check the fitment, and adjust all the details of the fitment steady and proper.
Please check the fitment and all the details regularly, fix the bolts and nuts as necessary.
■ The instruction of painting is just our recommendation, please paint it as you like.
ATTENTION
PARTS
QUANTITIES
LED LAMP
1 SET
LED LAMP
Use caulking glue
to fill the gap
between the product
and the body.
※ WALD SHOWCAR IS PAINTED LIKE THE PICTURE
(STEP 4)
Make clear coating for the
carbon parts of WALD Front Bumper.
Even for Carbon Products,
WALD Show Car is painted
in Matte Black for these parts.
The LED attachment of WALD Show Car
is painted in Matte Black.
※ Use heat resistant caulking glue
to fix the attached LED lamps.
MBMANUALS.COM
