background image

356.805.003 

28

 

Date: 2019-04-04 

TrackRunner Upright – Cheat Sheet

 

MODE 

Function 

 

DMX 
channel 

Function 

None, TrackRunner is stopped 

 

Position rough (Hi of a 16 bit DMX channel) 

None, TrackRunner is stopped 

 

Position fine (Lo of a 16 bit DMX channel) 

Manual down slow 

 

Set the maximum speed 

Manual down fast 

  4 

Set soft-limit 

LOW

 position, moving down 

Manual up slow 

  5 

Set soft-limit 

HIGH

 position, moving up 

Manual up fast 

 

51-54%    

Save settings 

Enabled 

None, TrackRunner is stopped 

 

 

Else 

    S

ave settings

  

Disabled 

Positioning with slow ramp 

 

 

Positioning with medium ramp 

 

Positioning with fast ramp 

 

 
           WARNING!  
Do not use the product  
if any damage is found! 
 
 
 
 
 

How to get started 

1.

 

Manually feed mains power to the unit and roll-on a secured track using mode 2 for top down or mode 4 for 
bottom up installation. 

2.

 

Apply DMX from a Lighting desk, ideally a desk with manual faders. 

3.

 

Make sure that your six channels are patched from DMX channel 1 to 6. 

4.

 

Pull all channels on to 0% 

5.

 

Apply power to the track and link the wireless DMX units by pressing (short push<½s) the LINK SW on both 
transmitter and receiver within 10s 

 

RF LINK, LINKED, STATUS(STAT) and DMX lamp should be lit when connected 

after the 10s (timeout of wireless search function).

 

6.

 

Set DMX channel 6 to 53% - 

This enables the saving of soft-limit low and high position.

 

7.

 

Pull channel 4 to 20 % -- the unit starts moving down.

 

8.

 

Stop the unit (pull channel 4 to 0%) when the desired LOW position is reached.

 

9.

 

Pull channel 5 to 20 % -- the unit starts moving up.

 

10.

 

Stop the unit (pull channel 5 to 0%) when the desired HIGH position is reached.

 

11.

 

Pull channel 1 (position) to 75 % 

12.

 

Pull channel 3 (speed) to 50% - 

The unit start to move up, with 50% speed, to a position that is 75%.

 

13.

 

Pull channel 1 (position) to 25% - T

he unit starts to move down, with 50% speed, to a position that is 25%

 

 
 
 

Before each use 

Inspect the 

product 

for 

damage

, wear, corrosion or abuse. 

Inspect  the 

moving  portion

  for 

damage

,  wear,  corrosion  or  abuse  and  make 

sure everything is 

safely attached

 and within the 

maximum loads

Check that the unit 

is securely mounted

 according to the user manual. 

Green LED indicators: 

LED next to the DMX address selectors. 

Glows constant: 

DMX connection is correct. 

Flashing: 

DMX signal is missing. 

LED next to the MODE selectors. 

Fast flashing: 

The motor needs to be reset, before it can be used. 

Slow flashing: 

The motor is moving towards the set position 

Steady light: 

The set position has been reached and the motor stopped. 

Individual LED

’s

 next to the antenna. 

20-80%: 

Indicates signal strength of linked transmitter. 

RF Link: 

Active radio link is available. 

Linked: 

Receiver linked to transmitter. 

DMX: 

DMX signal is present. 

STAT: 

Steady light indicates radio link and DMX present. 

Tech specs: 

General 

  Speed 

0.3m/s (1ft/s) 

  Maximum load  

20 kg (44 lb) 

  Weight 

13.3 kg (29.3 lb) 

 

Wireless 

  2.4 GHz ISM Band / 100mW (CRMX inside) 
  

LINK SW: 

  Short-push (<½s) 

Link to transmitter/receiver 

  Long-push (>3s) 

Unlink  from  transmitter  (Change  transmitter 
station) 

Содержание TrackRunner Upright





























Отзывы: