background image

356.805.003 

17

 

Date: 2019-04-04 

DMX channel overview 

DMX 
channel 

Function 

Description 

Position rough 

This channel controls the position of the unit, with the speed (DMX channel 3). 

This rough position works together with the fine position (DMX channel 2).  

The rough position and the fine position are multiplied in to a 16 bit channel. The rough 
position is the 

MSB

Position fine 

This channel controls the position of the unit, with the speed set on DMX channel 3.  

This fine position works together with the rough position (DMX channel 1).  

The fine position and the rough position are multiplied in to a 16 bit channel. The fine 
position is the 

LSB

 

Speed 

This channel controls the speed of the unit. 

This channel defines the maximum speed, and the motor slows down as closing in on the 
wanted position.  

This channel also works as a main brake; the motor does not run unless the channel is set 
above 0%. The speed-channel can also be used to make soft and slow movements or fast 
and sudden movements. 

Manuel Down 
/ Set soft-limit 
low (0% 
position) 

The  value  of  the  channel  determines  the  speed  at  which  the  unit  moves.  This  channel 
overrules movement with positioning via channel 1 & 2. 
 

 

Channel 6 

between

 51-54% enable save soft-limits. 

When channel 6 is in this range the lower position can be adjusted using channel 4.  
The lowest position is saved when channel 4 is put back at 0%. Note that it should be 
moved gradually towards 0% to give the motor time to slow down. 
The lowest position should be set  with channel 4 before the highest position is set 
with channel 5, since the range is calculated relative to the lowest position.  
 

 

Channel 6 

not between

 51-54% enable save soft-limits is 

NOT

 enabled. 

When save position is not enabled, channel 4 can still run the motor but any position 
is not saved, so it returns to the position given by channel 1 &2. 

Manuel Up / 
Set soft-limit 
high, and 
range (100% 
position) 

The  value  of  the  channel  determines  the  speed  at  which  the  unit  moves.  This  channel 
overrules movement with positioning via channel 1 & 2. 
 

 

Channel 6 

between

 51-54% enable save soft-limits. 

When channel 4 is in this range the end position can be adjusted when running with 
channel 5. The highest position is set when channel 5 is put back at 0%. 
The lowest position should be set  with channel  4 before the highest position is set 
with channel 5, since the range is calculated relative to the lowest position.  
 

 

Channel 6 

not between

 51-54% enable save soft-limits is 

NOT

 enabled. 

When save position is not enabled, channel 5 can still run the motor but any position 
is not saved, so it returns to the position given by channel 1 & 2. 

Enable save 
soft-limits 

When channel 6 is between 51-54% saving of soft-limit low and high position is enabled.  

The unit can be operated while channel 6 is between 51-54%, however, to minimise the risk 
of accidentally setting new low and high limits, channel 6 should be set to 0% when not in 
use. 

 

 

 

 

Содержание TrackRunner Upright





























Отзывы: