Wahlberg 352.701, Руководство пользователя

Страница: 32 / 32

352-353.805.006
32
Date: 2019-07-02
Track Runner Series – Cheat Sheet
MODE Function DMX Ch. Function
0, 1, 6 None, Track Runner is stopped 1 Position rough (Hi of a 16-bit DMX channel)
2 Manual REVERSE slow (no DMX needed) 2 Position fine (Lo of a 16-bit DMX channel)
3 Manual reverse fast (no DMX needed) 3 Set the maximum speed
4 Manual FORWARD slow (no DMX needed)
4
Set soft-limit REVERSE position, or move manually
5 Manual forward fast (no DMX needed)
5
Set soft-limit FORWARD position, or move manually
7 Positioning with slow ramp
6 51-54% Save soft limit Enabled
8 Positioning with medium ramp
Else S ave soft limit Disabled
9 Positioning with fast ramp
How to get started
1. Manually feed mains power to the unit and roll-on a secured track using mode 2 from the right side or mode 4
for from the left side (seen form the connections).
2. Apply DMX from a Lighting desk, ideally a desk with manual faders.
3. Make sure that your six channels are patched from DMX channel 1 to 6.
4. Pull all channels on to 0%
5. Apply power to the track and link the wireless DMX units by pressing (short push<½s) the LINK SW on both
transmitter and receiver within 10s
–
RF LINK, LINKED, STATUS(STAT) and DMX lamp should be lit when connected
after the 10s (timeout of wireless search function) or use the hard wiring through a cable carrier.
6. Set DMX channel 6 to 53% -
This enables the saving of soft-limit left and right position.
7.
Pull channel 4 to 20 % -- the unit starts moving reverse (left).
8. Stop the unit (pull channel 4 to 0%) when the desired LEFT end position is reached.
9.
Pull channel 5 to 20 % -- the unit starts moving forward (right).
10. Stop the unit (pull channel 5 to 0%) when the desired RIGHT end position is reached.
11. Pull channel 1 (position) to 75 %
12. Pull channel 3 (speed) to 50% -
The unit start to move reverse, with 50% speed, to a position that is 75%.
13. Pull channel 1 (position) to 25% - T
he unit starts to move forward, with 50% speed, to a position that is 25%
Before each use
−
Inspect the product for damage , wear, corrosion or abuse.
−
Inspect the moving portion for damage , wear, corrosion or abuse and make sure everything
is safely attached and within the maximum loads .
−
Check that the unit is securely mounted according to the user manual.
WARNING! Do use the product if any damage is found
Tech specs:
General
Maximum speed Slow motor 23 cm/s (9.1 in/s)
Fast motor 42 cm/s (16.5 in/s)
Load capacity 50 kg (110 lb)
Push capacity 500 kg (1102 lb)
Weight 10.8 kg (23.8 lb)
Wireless
2.4 GHz ISM Band / 100mW (CRMX inside)
LINK SW:
Short-push (<½s) Link to transmitter/receiver
Long-push (>3s) Unlink from transmitter (Change transmitter station)
Green LED indicators:
LED next to the DMX address selectors.
Glows constant: DMX connection is correct.
Flashing: DMX signal is missing.
LED next to the MODE selectors.
Fast flashing: The motor needs to be reset, before it can be used.
Slow flashing: The motor is moving towards the set position
Steady light: The set position has been reached and the motor stopped.
Individual LED ’s next to the antenna.
20-80%: Indicates signal strength of linked transmitter.
RF Link: Active radio link is available.
Linked: Receiver linked to transmitter.
DMX: DMX signal is present.
STAT: Steady light indicates radio link and DMX
present.