manualshive.com logo in svg

WAGO 750-464, Руководство пользователя

Поделиться
Скачать
WAGO 750-464 Скачать руководство пользователя страница 95

WAGO-I/O-SYSTEM 750 

Process Image 

95 

750-464 2/4 AI RTD configurable 

 

 

Manual 

 

Version 1.0.1  

 

7.5 

Data of the Version 750-464/020-000 (NTC, 
configurable) 

7.5.1 

NTC 10 kOhm 

With the setting "NTC 10 kOhm", the I/O module converts the resistance 
measured values of NTC 10kOhm resistance sensors and outputs them as 
temperature values.  
The temperature values are displayed at a resolution of 1 digit per 0.1 °C in one 
word (16-bit). Temperature values below 0 °C are represented in two's 
complement binary. As a result, 0 °C corresponds to the numeric value 0x0000 
and 100 °C to the numeric value 0x03E8 (dec. 1000).  
The possible numeric range corresponds to the defined temperature range of the 
sensors from -50 °C to +150 °C. 

Table 80: Process image for 750-464/020-000, NTC 10 kOhm setting 

Temperature 

°C 

Resistance 

k

Ω 

Numeric value 

1)

 

Status 

byte 

hex. 

LED 

error 

AI 1, 2 

Binary 

Hex. 

Dec. 

< -50.0 

>1144.48 

'1110.1100.0111.1000'  0xFE0C 

-500 

0x41 

on 

Underrange 

3)

 

-50.0 

1144.48 

'1110.1100.0111.1000'  0xFE0C 

-500 

0x00 

off 

0.0 

36.35 

'0000.0000.0000.0000' 

0x0000 

0 

0x00 

off 

25.0 

10.00 

'0000.0000.1111.1010' 

0x00FA 

250 

0x00 

off 

50.0 

3.36 

'0000.0011.0010.0000' 

0x01F4  

500 

0x00 

off 

100.0 

0.59 

'0000.0011.1110.1000' 

0x03E8 

1000 

0x00 

off 

150.0 

0.155 

'0000.0101.1101.1100'  0x05DC 

1500 

0x51 

off 

> 150.0 

< 0.155 

'0000.0101.1101.1100'  0x05DC 

1500 

0x42 

on 

Overrange 

3)

 

--- 

< 0.009 

'0000.0101.1101.1100'  0x05DC 

1500 

0x52 

on 

Short circuit 

2)

 

1)  Temperature values below 0 °C are represented in two's complement binary. 
2)  When short circuit and wire break monitoring is ON (see section "Behavior in the Event of an 

Error") 

3)  When underrange / overrange limit is ON (see section "Behavior in the Event of an Error") 

Содержание 750-464























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды