background image

1

WARNING

PREVENTION

HAZARD

General

• All accessories must be rated at or above the maximum

pressure rating of spray pump (includes spray tips, guns,
extensions and fluid hose.

• If you are injected, see a physician immediately.

Injection (Con't)

DO NOT TREAT AS A SIMPLE CUT! It can lead
to amputation.  See a physician immediately.

NOTE TO PHYSICIAN: Injection into the skin
is a traumatic injury. It is important to treat
the injury surgically as soon as possible. DO
NOT delay treatment to research toxicity.
Toxicity is a concern with some coatings
injected directly into the blood stream. Con-
sultation with a plastic surgeon  or recon-
structive hand surgeon may be advisable.

• Read all instructions and safety precautions before oper-

ating.

• Comply with all appropriate local, state and national

codes governing ventilation, fire prevention, and opera-
tion of Electrostatic equipment usage.

• The United States Government Safety Standards have

been adopted under the Occupational Safety and Health
Act. These standards, particularly the General Stan-
dards, Part 1910 and the Construction Standard, Part
1926, should be consulted.

• NFPA Standard No. 33 is to be followed when setting up

your spray area. Contact the National Fire Protection
Association, Batterymarch Park, Quincy, Massachusetts,
02269 for more information.

• Check with  insurance company for additional require-

ments.

• DO NOT substitute any other spray gun or power pack

with this system.  Use only identical replacement parts.

6

Содержание Stati-Kit 2000 0292003





















Отзывы: