background image

1

HAZARD

WARNING

• Follow the requirements of the Material Safety Data

Sheet supplied by the coatings manufacturer.

• Exhaust and fresh air introduction must be provided

within the spray area to keep the air free of accumula-
tions of toxic materials.

• Wear a mask or respirator.  Read all instructions for the

mask to insure that it will provide the necessary protec-
tion against the inhalation of harmful vapors.

PREVENTION

• Maximum operating range of the gun - 

3625 PSI fluid

pressure.

• NEVER aim the gun at any part of the body under any

circumstances.

• NEVER let any part of the body come in contact with the

fluid stream. DO NOT come in contact with a fluid stream
created by a leak in the fluid hose.

• Paint hose can develop leaks from wear, kinking, abuse

etc.  A leak is capable of injecting material into the skin.
Paint hose should be inspected before each use.  Re-
place a damaged hose.

• NEVER put hand in front of the gun.  Gloves will not

provide protection against an injection injury.

• ALWAYS lock the gun trigger when cleaning, changing

tips or leaving unattended.

• Some spray pumps prohibit the use of halogenated

hydrocarbon solvents.

• Halogenated hydrocarbon solvents such as methylene

chloride and 1,1,1 - Trichlorethane are not compatible
with aluminum and may cause an explosion. If you are
not sure of a material’s compatibility with aluminum,
contact your coatings supplier.  Halogenated hydrocar-
bon solvents are compatible with the GM2000 spray gun
and may be used if the solvents are compatible with the
pump and other accessories.

• ALWAYS shut fluid pump off and release all pressure

before  servicing, cleaning, or changing tips.

Toxic Substances: Some materials may be harm-
ful if inhaled or come in contact with the skin.

Explosion hazard incompatible materials.  May cause
property damage or severe injury.

Injection.  A high pressure stream of paint can pierce the
skin and underling tissues, leading to serious injury and
possible amputation.

5

Содержание Stati-Kit 2000 0292003





















Отзывы: