manualshive.com logo in svg

Wacker Neuson BS 60-4s, Руководство оператора

Поделиться
Скачать
Wacker Neuson BS 60-4s Скачать руководство пользователя страница 44

Tech Data

BS 60-4s

44                                       

wc_td000406gb.fm

8.2

Sound Measurements

Products are tested for sound pressure level in accordance with EN
ISO 11204. Sound power level is tested in accordance with European
Directive 2000/14/EC - Noise Emission in the Environment by
Equipment for use outdoors.

•

the sound pressure level at operator's location (L

pA

) = 91 dB(A).

06200074, 0620483, 0620812, 0620813,  0620820

•

the sound pressure level at operator's location (L

pA

) = 98 dB(A).

0620819, 0620388, 0620816

•

the guaranteed sound power level (L

WA

) = 108 dB(A).

8.3

Vibration Measurements

8.3.1

Products are tested for hand/arm vibration (HAV) level in accordance
with ISO 5349, EN1033, and EN500-4 where applicable.

•

HAV 6.5 m/s

2

Refer to Section 

Proper Operation

 for further details.

8.3.2

HAV Uncertainties

Hand-transmitted vibration was measured per ISO 5349-1. This 
measurement includes an uncertainty of 1.5 m/sec

2

.

Содержание BS 60-4s

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды