manualshive.com logo in svg

Wacker Neuson BS 60-4s, Руководство оператора

Поделиться
Скачать
Wacker Neuson BS 60-4s Скачать руководство пользователя страница 28

Operation

BS 60-4s

28                                       

wc_tx001488gb.fm

5

Operation

5.1

Preparing the Machine for First Use

Preparing for first use

To prepare your machine for first use:

5.1.1

Make sure all loose packaging materials have been removed from the 
machine.

5.1.2

Check the machine and its components for damage. If there is visible 
damage, do not operate the machine! Contact your Wacker Neuson 
dealer immediately for assistance.

5.1.3

Take inventory of all items included with the machine and verify that 
all loose components and fasteners are accounted for.

5.1.4

Attach component parts not already attached.

5.1.5

Add fluids as needed and applicable, including fuel, engine oil, and 
battery acid.

5.1.6

Move the machine to its operating location.

5.2

Recommended Fuel

This engine is certified to operate on automotive unleaded gasoline.
Use only fresh, clean gasoline. Gasoline containing water or dirt will
damage fuel system. 

Содержание BS 60-4s

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды