manualshive.com logo in svg

Wacker Neuson BS 60-4s, Руководство оператора

Поделиться
Скачать
Wacker Neuson BS 60-4s Скачать руководство пользователя страница 11

Emission Control System Information

wc_tx000369gb.fm

11

PARTS COVERED

  

Listed below are the parts covered by the Emission Components
Defect Warranty. Some of the parts listed below may require
scheduled maintenance and are warranted up to the first scheduled
replacement point for that part.

(1) Fuel Metering System 

(i) Carburetor and internal parts (and/or pressure regulator or fuel

injection system).

(ii) Air/fuel ratio feedback and control system, if applicable.

(iii) Cold start enrichment system, if applicable.

(iv) Regulator assembly (gaseous fuel, if applicable) .

(2) Air Induction System

(i) Intake manifold, if applicable.

(ii) Air filter.

(3) Ignition System

(i) Spark plugs.

(ii) Magneto or electronic ignition system. 

(iii) Spark advance/retard system, if applicable.

(4) Exhaust manifold, if applicable

(5) Miscellaneous Items Used in Above Systems

(i) Electronic controls, if applicable.

(ii) Hoses, belts, connectors, and assemblies.

(iii) Filter lock assembly (gaseous fuel, if applicable).

Содержание BS 60-4s

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды