WACKER Group LTC 4 Скачать руководство пользователя страница 74

Страница: 74 / 166

Lombardini Engine Troubleshooting

LTC Repair

wc_tx000364gb.fm

5.8

Checking Voltage to Glow Plugs (Lombardini 1003 engines)

See Graphic: wc_gr003229

To check the voltage to the glow plugs, carry out the following
procedure:

5.8.1

Disconnect the B (black) wire (a), place the keyswitch in the START
position, and measure the voltage between the black wire and ground.
There should be 12V (battery voltage approximately 12) measured.

•

If 12V is measured, check the function of the glow plug.

•

If 12V is not measured, continue.

5.8.2

Disconnect the B (black) wire (b) and measure the voltage between it
and ground. There should be 12V (battery voltage approximately 12)
measured.

•

If 12V is measured, clean the connection points of the wires.
Reconnect the wires and check the function of the glow plug.

•

If 12V is not measured, check the glow plug relay.

wc_gr003229

Содержание LTC 4







































































































































































Результаты поиска

Содержание LTC 4

Отзывы:

Бренды по названию

Популярные бренды

WACKER Group LTC 4, Руководство по ремонту

Результаты поиска

Содержание LTC 4

Отзывы:

Бренды по названию

Популярные бренды