WACKER Group LTC 4 Скачать руководство пользователя страница 67

Страница: 67 / 166

LTC Repair

Lombardini Engine Troubleshooting

wc_tx000364gb.fm

5.2

Engine Does Not Crank—Flowchart 3A

Check battery voltage.

the black wire

connected?

Yes

wc_gr003083

Check for battery voltage between
terminal 30 of keyswitch and ground.

Reconnect

black wire.

Clean and

tighten connections.

Repair wiring

from terminal 30

to battery.

Are

connections clean

and tight?

Yes

Recharge or

replace battery.

Does

battery measure

11.0–13.0V?

Yes

Check for battery voltage between
terminal 50 and ground when key
is placed in the START position.

Engine Does Not Crank

Is battery

voltage measured

between 30 and

ground?

Yes

Replace keyswitch.

Is battery

voltage measured

between 50 and

ground?

Yes

Check for battery voltage
between black wire at starter
solenoid and ground when
key is in START position.

Repair/replace

black wire.

Consult

Lombardini

engine repair

manual.

Is battery

voltage measured

between black wire

and ground?

Yes

Checking Keyswitch and Wiring

Check connection of black wire at
starter solenoid. Also check wire
connections at back of keyswitch.

Содержание LTC 4







































































































































































Результаты поиска

Содержание LTC 4

Отзывы:

Бренды по названию

Популярные бренды

WACKER Group LTC 4, Руководство по ремонту

Результаты поиска

Содержание LTC 4

Отзывы:

Бренды по названию

Популярные бренды