manualshive.com logo in svg

WACKER Group LTC 4, Руководство по ремонту

Поделиться
Скачать
WACKER Group LTC 4 Скачать руководство пользователя страница 152

Disassembly/Assembly Procedures

LTC Repair

wc_tx000428gb.fm

148

8.10 Main Mast

See Graphic: wc_gr02434

Disassembly:

Turn the lights off, turn the unit off, and lower the mast assembly into
the cradle before performing this procedure. Place the Light Tower in
a position with enough room so that the masts may be extended fully
while in the down position.

The mast cable system consists of two cables: one connected to the
winch mounted on the main mast that raises the mid mast; and a
second that is connected to both the upper mast and the main mast.
This second cable raises the upper mast as the mid mast is being
raised.

8.10.1

Remove the upper mast and the mid mast from the main mast. See
section Mid Mast.

8.10.2

Disconnect the wiring from the control panel by:

•

Snipping the wire ties (a).

•

Disconnecting the wires from the capacitors (b).

•

Disconnecting the wires from terminal strip (c).

8.10.3

Loosen the clamps (d & e) securing the tower supply cable. One is
located on the control box and the other is on the front enclosure panel.

8.10.4

Remove the cable clip (f) from the underside of the enclosure top.

8.10.5

Thread the tower supply cable through the eyes (g) on the side of the
main mast.

8.10.6

Remove the cable clip (h) attached to the end of the main mast.

8.10.7

Tighten the adjusting knob (i) so that the main mast will not spin when
loosening the nut (j)  securing the main mast to the main cradle.
Remove the nut securing the main mast to the main cradle.

8.10.8

Loosen the adjusting knob.

8.10.9

Using an appropriate crane or hoist, lift the main mast up and out of the
main cradle and free from the machine.

Содержание LTC 4







































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды