WACKER Group 0007587, Руководство по ремонту

Страница: 41 / 44

Use Of Threadlockers and Sealants
Threadlocking adhesives and sealants are specified throughout this manual and should be used where indicated.
Threadlocking compounds normally break down at temperatures above 350° F (175° C). If a screw or bolt is hard
to remove, heat it using a small propane torch to break down sealant. When applying sealants, follow instructions
on container. The sealants listed below are recommended for use on WACKER equipment.
SEALANTS
TYPE
( ) = Europe
COLOR USAGE PART NO. - SIZE
Loctite 222 Purple Low strength, for locking threads smaller than 1/4" (6 mm). 73287 - 10 ml
Hernon 420 Hand tool removable.
Omnifit 1150 (50M) Temp. range, -65 to 300 degrees F (-54 to 149 degrees C)
Loctite 243 Blue Medium strength, for locking threads larger than 1/4" (6 mm). 29311 - .5 ml
Hernon 423 Hand tool removable. 17380 - 50 ml
Omnifit 1350 (100M) Temp. range, -65 to 300 degrees F (-54 to 149 degrees C)
Loctite 271 / 277 Red High strength, for all threads up to 1" (25 mm). 29312 - .5 ml
Hernon 427 Heat parts before disassembly. 26685 - 10 ml
Omnifit 1550 (220M) Temp. range, -65 to 300 degrees F (-54 to 149 degrees C) 73285 - 50 ml
Loctite 290 Green Medium to high strength, for locking preassembled threads 28824 - .5 ml
Hernon 431 and for sealing weld porosity (wicking). 25316 - 10 ml
Omnifit 1710 (230LL) Gaps up to 0.005" (0.13 mm)
Temp. range, -65 to 300 degrees F (-54 to 149 degrees C)
Loctite 609 Green Medium strength retaining compound for slip or press fit 29314 - .5 ml
Hernon 822 of shafts, bearings, gears, pulleys, etc.
Omnifit 1730 (230L) Gaps up to 0.005" (0.13 mm)
Temp. range, -65 to 300 degrees F (-54 to 149 degrees C)
Loctite 545 Brown Hydraulic sealant 79356 - 50 ml
Hernon 947 Temp. range, -65 to 300 degrees F (-54 to 149 degrees C)
Omnifit 1150 (50M)
Loctite 592 White Pipe sealant with Teflon for moderate pressures. 26695 - 6 ml
Hernon 920 Temp. range, -65 to 300 degrees F (-54 to 149 degrees C) 73289 - 50 ml
Omnifit 790
Loctite 515 Purple Form-in-place gasket for flexible joints. 70735 - 50 ml
Hernon 910 Fills gaps up to 0.05" (1.3 mm)
Omnifit 10 Temp. range, -65 to 300 degrees F (-54 to 149 degrees C)
Loctite 496 Clear Instant adhesive for bonding rubber, metal and plastics;
Hernon 110 general purpose. 52676 - 1 oz.
Omnifit Sicomet 7000 For gaps up to 0.006" (0.15 mm)
Read caution instructions before using.
Temp. range, -65 to 180 degrees F (-54 to 82 degrees C)
Loctite Primer T Aerosol Fast curing primer for threadlocking, retaining and 2006124 - 6 oz.
Hernon Primer 10 Spray sealing compounds. Must be used with stainless steel
Omnifit VC Activator hardware. Recommended for use with gasket sealants.