WABCO 400 500 320 0 Скачать руководство пользователя страница 88

Страница: 88 / 188

Diagnostics

Blink
Code

SPN

FMI

Suspect
Component
and Location

ITP
Function

Fault
Description
(FMI)

Cause

Repair Information

1760

3 Diagnostic

Connector

N/A

Subsystem

Power
Terminal -
(Cl30)
Voltage
Above
Normal or
Shorted High

A short circuit to

supply voltage
was detected at
Subsystems pin 1
(cl.30).

- Check the cable between

modulator and the connected
component.
- Check for tight seat of the
connectors.
- Test the cable for continuity
from end to end.
- Check whether water or
moisture has entered into one
of the connectors and check
the seals for proper

- Check whether the cable is
frayed.
- If no other fault can be
found, replace the connected
components.

1760

4 Diagnostic

Connector

N/A

Subsystem

Power
Terminal -
(Cl30)
Under-
voltage/
Short Circuit
to Ground

A short circuit

to ground was
detected at
Subsystems pin 1
(cl.30).

- Check the cable between

- Check whether the cable is
frayed.
- If no other fault can be
found, replace the connected
components.

1760

6 Diagnostic

Connector

N/A

Subsystem

Power
Terminal -
(Cl30)
Current
Too High
or Circuit
Grounded

Overload was

detected at
subsystem pin 1
(cl.30).

- Check the cable between

- Check whether the cable is
frayed.
- If no other fault can be
found, replace the connected
components.

Содержание 400 500 320 0





























































































































































































Результаты поиска

Содержание 400 500 320 0

Отзывы:

Похожие инструкции для 400 500 320 0

Бренды по названию

Популярные бренды

WABCO 400 500 320 0, Руководство по обслуживанию

Результаты поиска

Содержание 400 500 320 0

Отзывы:

Похожие инструкции для 400 500 320 0

Бренды по названию

Популярные бренды