Vulcan-Hart ML-126610 страница 25 Скачать руководство пользователя

Страница: 25 / 75

If the average temperature
still differs

more

than 10°F

from the dial setting, adjust
the thermostat calibration
until the average
temperature is within
tolerance.

If the above adjustment cannot be obtained,
replace the temperature control and check
calibration.

UNITS AFTER JUNE 2013

Place a thermocouple in the geometric center of
the oven cavity.

Set the ON-OFF-COOL DOWN switch to ON.

Set the NORMAL - GENTLE BAKE switch to
NORMAL.

Set the temperature control dial to 350°F.

Allow the oven temperature to stabilize (normally
3 cycles).

Record the temperature at which the Heat lamp
goes OFF and comes ON for at least two
complete heating cycles.

Calculate the differential by subtracting the
temperature indicated when the lamp goes out
from the temperature indicated when the lamp
comes on.

Differential = Heat lamp OFF - Heat lamp ON

Example: 360° (lamp off) - 340° (lamp on) =
20°

The differential calculated should be

less

than 20°F.

If the differential is

less

than 20°F, the

temperature control circuit is
functioning properly.

Proceed to STEP 8.

If the differential is

more

than 20°F:

Check the temperature probe as
outlined under TEMPERATURE
PROBE TEST.

If the probe is functioning properly
then temperature control is
malfunctioning.

Install a replacement
temperature control and
check calibration.

Calculate the average temperature by adding the
temperature indicated when the lamp goes out to
the temperature indicated when the lamp comes
on and dividing this answer by 2.

[Temp. (lamp off) + Temp. (lamp on)] ÷ 2 =
Average Temp. Example: (360° + 340°) ÷ 2 =
350°

If the average temperature is

less

than 10°F

from the dial setting, the thermostat is
properly calibrated.

If the average temperature is

more

than

10°F from the dial setting, the thermostat
calibration must be adjusted.

Loosen the temperature control knob
set screw and remove the knob from
the stem.

Access the adjustment potentiometer
located at the 3 o'clock position.

Turn

clockwise

to increase,

counterclockwise

to decrease

temperature

Repeat the average temperature
calculation in STEP 8.

NOTE:

Allow the oven to cycle at least two times

between adjustments before performing the
calculation.

If the average temperature
still differs

more

than 10°F

from the dial setting, adjust
the thermostat calibration
until the average
temperature is within
tolerance.

If the above adjustment cannot be obtained,
replace the temperature control and check
calibration.

MECHANICAL THERMOSTAT

CALIBRATION (VC4GS/6GS)

Place a thermocouple in the geometric center of
the oven cavity.

Set the ON-OFF-COOL DOWN switch to ON.

Set the thermostat dial to 350°F.

Allow the oven temperature to stabilize (normally
3 cycles).

Record the temperature when the thermostat
cycles OFF and ON for at least three complete
cycles.

VC4G & VC6G SERIES FULL SIZE CONVECTION OVENS - SERVICE PROCEDURES AND ADJUSTMENTS

Page 25 of 75

F24682 Rev. D (1016)

Содержание ML-126610












































































Результаты поиска

Содержание ML-126610

Отзывы:

Похожие инструкции для ML-126610

Бренды по названию

Популярные бренды

Vulcan-Hart ML-126610, Руководство по обслуживанию

Результаты поиска

Содержание ML-126610

Отзывы:

Похожие инструкции для ML-126610

Бренды по названию

Популярные бренды