Vulcan-Hart ML-126610 страница 19 Скачать руководство пользователя

Страница: 19 / 75

Fig. 42

If replacing the bottom bearing, remove it
from the door shaft or the lower sill opening.

Reverse procedure to install door assembly and
check for proper adjustment as outlined under
DOOR ADJUSTMENT and DOOR SWITCH
ADJUSTMENT.

DOOR CATCH BALL ASSEMBLY

(INDEPENDENT DOORS)

NOTE:

For units with serial number starting with 48

made before 8/13/07 and serial number starting with
54 made before 8/27/07.

Disconnect the

electrical power to the machine and
follow lockout / tagout procedures.

Remove the FRONT COVER.

Remove the screws that secure the door catch
assembly.

Fig. 43

Reverse procedure to install.

Adjust the ball catch as outlined under DOOR
CATCH BALL ADJUSTMENT (INDEPENDENT
DOORS).

ROLLER LATCH ASSEMBLY

(INDEPENDENT DOORS)

NOTE:

For units with serial number starting with 48

made after 8/12/07 and serial number starting with 54
made after 8/26/07.

Disconnect the

electrical power to the machine and
follow lockout / tagout procedures.

Remove the screws that attach roller latch
assembly to door.

Fig. 44

Reverse procedure to install.

DOOR WINDOW

Disconnect the

electrical power to the machine and
follow lockout / tagout procedures.

Remove the screws at the top and bottom of
door.

VC4G & VC6G SERIES FULL SIZE CONVECTION OVENS - REMOVAL AND REPLACEMENT OF PARTS

Page 19 of 75

F24682 Rev. D (1016)

Содержание ML-126610












































































Результаты поиска

Содержание ML-126610

Отзывы:

Похожие инструкции для ML-126610

Бренды по названию

Популярные бренды

Vulcan-Hart ML-126610, Руководство по обслуживанию

Результаты поиска

Содержание ML-126610

Отзывы:

Похожие инструкции для ML-126610

Бренды по названию

Популярные бренды