background image

– 6 –

7. Pull the high limit bulb through the underside

of the fry tank and remove the high limit
assembly.

8. Reverse the procedure to install. When

installing the new high limit assembly, do not
kink the high limit capillary. Wrap threads of
packing nut with Teflon tape to prevent
leakage.

THERMOPILE

WARNING: 

SHUT OFF THE GAS BEFORE

SERVICING.

WARNING: 

ALL GAS JOINTS DISTURBED DURING

SERVICING MUST BE CHECKED  FOR LEAKS.
CHECK WITH SOAP AND WATER SOLUTION
(BUBBLES). DO NOT USE AN OPEN FLAME.

1. Disconnect thermopile lead wires as outlined

under High Limit.

2. Remove (1) 10-24 screw and pull the pilot

assembly away from the tank body.

3. Remove (2) side screws to detach the pilot

from the holding bracket.

4. Remove pilot tubing from pilot.

5. Remove screws holding pilot bracket.

HIGH LIMIT

WARNING: 

SHUT OFF THE GAS BEFORE

SERVICING.

1. Drain shortening from fry tank.

2. Remove wire leads from high limit, noting all

connections for reassembly.

3. Remove high limit from mounting bracket.

4. Remove left burner as outlined under Burners.

5. Loosen the packing nut and the holding nut.

6. Remove the high limit bulb from the clamp.

Содержание GHF90G

















Отзывы: