background image

– 2 –

© VULCAN-HART, 2004

TABLE OF CONTENTS

GENERAL .............................................................................................................................................................. 3

Introduction ............................................................................................................................................... 3
Installation ................................................................................................................................................ 3
Oil Filtering ................................................................................................................................................ 3
Operation ................................................................................................................................................... 3
Cleaning .................................................................................................................................................... 3
Lighting Pilot ............................................................................................................................................. 3
Specifications ........................................................................................................................................... 3

Gas Data ............................................................................................................................................. 3

Tools ......................................................................................................................................................... 3

Standard ............................................................................................................................................. 3

REMOVAL AND REPLACEMENT OF PARTS ..................................................................................................... 4

Covers and Panels ................................................................................................................................... 4

Door .................................................................................................................................................... 4
Front Panel ......................................................................................................................................... 4

Burners ...................................................................................................................................................... 4
Thermostat ................................................................................................................................................ 5
High Limit .................................................................................................................................................. 6
Thermopile ................................................................................................................................................ 6
Pilot Orifice ............................................................................................................................................... 7
Combination Valve ................................................................................................................................... 7
Fry Tank .................................................................................................................................................... 8

SERVICE PROCEDURES AND ADJUSTMENTS ............................................................................................. 9

Millivolt Controls Test .............................................................................................................................. 9
Thermostat Calibration ............................................................................................................................. 9

Calibration Steps ................................................................................................................................ 9

Pilot Adjustment ...................................................................................................................................... 10
Burners, Nozzles and Orifices ................................................................................................................ 10

Burners .............................................................................................................................................. 10
Nozzles and Orifices ......................................................................................................................... 10

Combination Valve Regulator Adjustment .............................................................................................. 11

ELECTRICAL OPERATION ................................................................................................................................ 12

Control System Description .................................................................................................................... 12
System Condition Quick Check Procedures .......................................................................................... 12
Schematic ................................................................................................................................................ 13
Component Function ............................................................................................................................... 13

TROUBLESHOOTING ......................................................................................................................................... 14

Содержание GHF90G

















Отзывы: