background image

128-9304

 26 of 28

26

Programmable Features Bank 3 Is Remote Start Selectable Features:

Feature Selection

 

 

1 Chirp

 

 

2 Chirps

 

 

3 Chirps

 

 

4 Chirps

 

 

5 Chirps

 

 

6 Chirps

 

 

1st Defrost Output

 

 

Pulsed

 

 

10 

Mins

 

         

2nd RF Start Chirp

  

Of

 

On

 

 

On & Carfinder

 

      

3rd Run 

Time

 

 

5 Mins

 

 

10 Mins

 

 

15 

Mins

 

 

20 

Mins

 

 

45 

Mins

 

 

60 

Mins

 

  

4th Parking Lights

 

 

On Steady

 

Flashing

 

         

5th Input Check

 

 

Voltage

 

 

Tach

  

DBI 

Tach

  

Hybrid

 

      

6th V

oltage Level

 

 

>0.5V B4 Start

 

0.5V 

B4 

Start

 

        

7th Ign. 2 Select

 

 

Of

f During Crank

 

On During Crank

 

Same 

As 

Accy

      

8th Ign. 3 Select

 

 

Of

f During Crank

 

On During Crank

 

Same 

As 

Accy

 

Same 

As 

Starter

 

     

9th Accy

. Relay

 

 

Off During Crank

 

On During Crank

 

Same 

As Starter

10th Diagnostics

 

 

Off

 

 

On

 

         

11th Crank 

Time

 

 

0.8 Sec

 

 

1.0 Sec

 

 

1.5 Sec

 

 

2.0 Sec

 

 

 3.0 Sec

 

 

 4.0 Sec

 

 

 

12th Gas/Diesel

 

 

Gas

 

 

Diesel 

10

  

Diesel 

15

  

Diesel 

20

      

13th T

emp 

Start

 

 

Not A

vailable

 

      

14th 

Crank A

veraging

 

Averaging

 

Preset T

ime

 

Note:

 When averaging, the engine must be started

       

times 

with 

the 

key 

to 

be 

ef

fective.

 

     

15th R/S Shock

 

 

Not A

vailable

 

      

16th T

urbo 

Select

 

 

Off

 

 

3 Mins

 

 

5 Mins

 

 

10 Mins

17th 

One or 

Two Press Start

 

Two Press

 

One Press

18th  Door Lock Control

 

No Change

 

Unlock Before & 

 

 Unlock Before

 

Lock 

After Start

     

Lock 

After Start

 

 Start

19th 

Alt O/P

 Before Start

 

Single Pulse

 

As Feat 1 Bank 2

 

350mS Pulse

 

500mS Pulse

 

800mS Pulse

20th 

Alt O/P

 During Crank

 

During Crank

 

Gnd When Running

 O/P

 Same as Ign 1

 O/P

 Same 

As 

Accy

 

21st Alt 

O/P

 After 

Start

 

Pulse After 

Start

 

Gnd When Running

 O/P

 Same as Ign 1

 O/P

 Same 

As 

Accy

O/P

 During Crank

22nd 

Alt O/P

 Aft Shut Dwn

 

Pulse 

Aft Sht Dwn

 Gnd When Running

 O/P

 Same as Ign 1

 O/P

 Same 

As 

Accy

O/P

 During Crank

23rd Ign & 

Accy Relays

 

No Pulse w/Unlock

 Pulse Ign, 

Accy

, &

 

Pulse Ign, 

Accy

, & 

 

 

 

 

 

     

GWR 

w/Unlock

 

GWR 

w/Unlock

       

Follow 

w/ASD

       

Pulse

 

  

NOTE: If 

feature #5 is set for V

oltage or Hybrid, the unit must also have feature #14 set for averaging or the Pk. Lts. will flash 7 times and the unit not start.

Содержание PRO9276E Pursuit Series





























Отзывы: