Voxx PRO9276E Pursuit Series страница 24 Скачать руководство пользователя

Страница: 24 / 28

128-9304

24 of 28

SELECT

ABLE FEA

TURES

The selectable features of this unit can be set manually as explained above, or online by using our web link.

The

Accessory VE-PROG kit will include the nec

essary cables to connect to your computer along with the web access information and application required to take advantage of this feature. Factory default settings are indicated by

BOLD

text below

NOTE:

The method of manual

override

can either be selected to operate

from the valet switch or operate by custom code. Custom Code program

ming is found

in the owners guide. Be certain to place a check mark indicating the method used in the box located on the last page of the owner's manual.

NOTE:

Manual programming Keyless Entry Models with no horn output will Flash the Parking Lights instead of chirp where chirp is indicated.

Also, No data will be indicated if a feature is not available for a particular model.

The unit will enter the feature but no selection will be available.

RF Programmable Feature Bank 1 Is For T

ransmitter Programming See T

ransmitter Programming Guide.

Programmable Features Bank 2 Is

Alarm Selectable Features:

Feature Selection

1 Chirp

2 Chirps

3 Chirps

4 Chirps

5 Chirps

6 Chirps

1st DoorL/UL

500

3.5 Sec.

500mS L, Dbl. U/L

Dbl L, 500mS UL

Dbl L, Dbl UL

500mS/350mS ul

2nd

Accy Lock

Auto Lock On

Auto Lock Off

3rd

Accy

. UL

Auto UL

All

Auto UL

Off

4th Headlights

Not A

vailable

5th Passive Locks

Not A

vailable

6th Pass/Act

Arm

Not A

vailable

7th Siren/Horn

Not A

vailable

8th Horn Chirp

10mS

16mS

30mS

40mS

50mS

9th O/R Method

Not A

vailable

10th 2 Step U/L

Off

1th Chp Del

Off

12th

Trigger Circuits

Not A

vailable

13th L/UL

Poll

Not A

vailable

14th

Aux Ch 5 Sel

Pulse

Push & Hold

10 Sec

20 Sec

Latch On/Of

Hold 3/S For O/P

15th

Aux Ch 6 Sel

Pulse

Push & Hold

10 Sec

20 Sec

Latch On/Of

Hold 3/S For O/P

16th

Aux Ch 7 Sel

Pulse

Push & Hold

10 Sec

20 Sec

Latch On/Of

Hold 3/S For O/P

17th

Trigger Delay

Not A

vailable

18th Data Port Select

DBI Protocol

ADS Protocol

If Programming via PC while connected to + 12 VDC you must manually enter the programming mode as shown below

Turn the ignition on Press and release valet switch 3 times

Turn ignition off then on, off then on, off then on, off then on to enter web/on-line feature selection Bank 5.

Siren chirps 5 times indicating access to feature program mode. Launch the application on your PC. Connect the module via the USB to DBI

harness and follow program prompts.

Содержание PRO9276E Pursuit Series





























Результаты поиска

Содержание PRO9276E Pursuit Series

Отзывы:

Похожие инструкции для PRO9276E Pursuit Series

Бренды по названию

Популярные бренды

Voxx PRO9276E Pursuit Series, Инструкция по установке

Результаты поиска

Содержание PRO9276E Pursuit Series

Отзывы:

Похожие инструкции для PRO9276E Pursuit Series

Бренды по названию

Популярные бренды