Voxx PRO9276E Pursuit Series Скачать руководство пользователя

Страница: 12 / 28

128-9304

12 of 28

18 LT. Blue w/ Black trace Wire:

(-) 300mA Selectable Output Channel 6

The light blue/green wire pulses to ground via an independent RF channel from the keychain transmitter.

This is a transistorized, low current output, and should only be used to drive an external relay coil.

WARNING:

Connecting the light blue/black to the high current circuits, will damage the control module.

Connect the light blue/black to terminal 86 of a 30 A automotive relay and wire the remaining relay contacts

to perform the selected function of channel 6.

19 LT. Blue w/ Green trace Wire:

Delayed 300 mA PULSED OUTPUT / CHANNEL 5

The light blue/green wire pulses to ground via an independent RF channel from the keychain transmitter.

This is a transistorized, low current output, and should only be used to drive an external relay coil.

WARNING:

Connecting the light blue/green to the high current switched output of trunk release circuits,

and some remote start trigger inputs, will damage the control module.

Connect the light blue/green to terminal 86 of a 30 A automotive relay, and wire the remaining relay con-

tacts to perform the selected function of channel 5.

20 Gray w/ Black trace Wire:

Negative Inhibit Input/Trigger When Armed

The Grey w/ Black Trace wire provides an instant shutdown for the Remote Start Control Module whenever

it is grounded. Connect the Grey w/ Black trace wire to the hood pin switch previously installed. This wire

must be routed through a grommet in the firewall and connected to the hood pin switch. If connecting

to a factory hood pin switch, or separate alarm it is recommended that a double diode circuit be used to

prevent feed back of one device to the other.

IMPORTANT!

This connection is a safety wire and must be connected as shown and tested as specified.

Failure to do so may result in personal injury or property damage. See detail of wiring in the following

diagram. This wire may also be used if the vehicle brake light circuit switches ground to the brake lights.

An isolation diode must be used for ground switched brake light circuits and must be connected to the

output of the brake switch.

Содержание PRO9276E Pursuit Series





























Результаты поиска

Содержание PRO9276E Pursuit Series

Отзывы:

Похожие инструкции для PRO9276E Pursuit Series

Бренды по названию

Популярные бренды

Voxx PRO9276E Pursuit Series, Инструкция по установке

Результаты поиска

Содержание PRO9276E Pursuit Series

Отзывы:

Похожие инструкции для PRO9276E Pursuit Series

Бренды по названию

Популярные бренды