Voxx Directechs DS3+ Скачать руководство пользователя страница 5

Страница: 5 / 21

DS4+ HONDA7

Pre-installation and application warnings

START

HERE

This section highlights important information for this specific firmware and will assist in pricing accordingly, as
well as bringing awareness to any operational or vehicle limitations.

Compatibilities and Requirements

T-Harness
compatible

THHON3

Keys
required for
programming

Keys required
for operation

Vehicle Takeover

Refer to the

Quick Reference Guide

section for more details.

Firmware notes

Important! A DS4+ module is required for this installation, as the Relay harness (H2), 10-pin white connector is used.

The optional Plug & Play THHON3 T-Harness is sold separately.

Important! All T-Harness wires NOT listed in the diagram are NOT required for the installation. Loose wires such as Siren Output and

Hood Input may need to be pulled from the tapped section of the T-Harness. Refer to the “Wiring diagram with T-Harness” for more

information on connections and installation instructions.

Important! DO NOT turn vehicle Ignition ON with ANY vehicle connectors disconnected, including during module programming.

Failure to do so may result with errors in the instrument cluster or hidden error messages.

It is possible to get a "Keyless Starting Error" message when remote started. This message will disappear when the vehicle is started
with the key.

Power liftgate and sliding door controls are ONLY available when the engine is OFF (where applicable).

Key2GO may be required if the interface does not program using the traditional method. Refer to "Module programming" for more

information.

Unless specified otherwise, all connectors are displayed from the wire side, with the exception of the OBDII diagnostic connector.

It is important to check that the fuses are positioned correctly in the module. Proper fuse positioning is displayed on each wiring
diagram.

Refer to the "Vehicle connections" section following the installation diagram.

Footnotes

[1]

The installation of an aftermarket hood pin is ONLY required on vehicles that are NOT equipped with a factory hood pin or if NOT
supported in data.

[2]

The siren is ONLY required when enabling the security features during module flashing.

[3]

The Green wire is OPTIONAL for starter disable and anti-grind applications.

Содержание Directechs DS3+






















Результаты поиска

Содержание Directechs DS3+

Отзывы:

Похожие инструкции для Directechs DS3+

Бренды по названию

Популярные бренды

Voxx Directechs DS3+, Руководство по установке

Результаты поиска

Содержание Directechs DS3+

Отзывы:

Похожие инструкции для Directechs DS3+

Бренды по названию

Популярные бренды