Voxelab Aquila Pro, Руководство пользователя

Страница: 27 / 32

25
Trouble Shooting
故障检修
Q：
A：
Q：What if the accuracy of model is not good?
A：Please ensure the normal tension of the synchronous belt, neither loose
nor tight.
Q：What if the screen turns dark?
A：1. Please check whether the wire of screen has those questions: loose,
plugged in reverse, plugged in wrong position, tilted plugging;
2. Refresh the firmware to see if the screen can recover to normal;
3. Contact the after-sales personnel if necessary.
Q：What if the nozzle cannot be heated?
A：1. Please check the temperature on display screen; if the temperature is
shown abnormal, it is in the reason of thermistor. Please replace the
thermistor and try again；
2. If the temperature is shown normal, it may be in the reason of heating
cable. Please replace the heating cable and try again.
Q：What if the axis cannot be moved?
A：1. Check the wire of the electric motor；
2. Contact us by email listed.
Email: support@voxelab3dp.com
Q：What if the files are garbled and cannot be read?
A： Repair the model before slicing.
Q：What if the build plate cannot be heated?
A：Please check the digital display of the temperature. If the temperature is
improper, please replace the thermistor. Otherwise, please replace the
heating wires.
What if the model warps or is unable to stick to the build plate?
1. The temperature of build plate was too low; increase its temperature
accordingly；
2. Filament failed to adhere or bond on the build plate, use glues to
enhance the adhesion；
3. Distance between the build plate and the nozzle is too far or the build
plate is not leveling enough; re-leveling the build plate accordingly.
文件乱码了，读取不了？
切片前请修复模型。
打印模型起翘，粘不住打印平台怎么办？
1. 平台温度设置太低，请加高平台温度；
2. 材料本身不粘平台（建议涂抹胶水，增强粘附力）；
3. 平台与喷嘴距离太大，平台未调平，请重新调平。
模型打印尺寸不良怎么办？
确认同步带是否异常松或太紧，调整到合适状态。
黑屏或显示不良怎么办？
1. 检查屏幕线束是否松动、插反、未插到位或倾斜错位，重新插拔一下；
2. 重装固件，是否能恢复，若不能请联系技术支持。
热床无法加热。
查看温度显示是否异常，若异常则热敏电阻损坏，需要更换热敏电阻；温度显示正
常不加热，加热板线损坏，需更换。
喷嘴不加热。
1. 查看温度显示是否异常，若异常则热敏电阻损坏，需要更换热敏电阻；
2. 温度显示正常不加热，加热管线损坏，需更换。
轴无法运动。
1. 检查电机线束是否插好；
2. 联系技术支持。
Q：
A：
What if knock and noise occur when nozzle returning to zero point?
1. Check whether the zero sensor is knocked and broken;
2. Check the lines and see whether the noises stop when pressing the
sensor by hand;
3. Contact us by email.
Email: support@voxelab3dp.com
回零一直在撞击 ，停不下来，有异响产生。
1. 确认回零传感器是否有问题，是否有碰撞到传感器；
2. 检查线路是否异常，手动按压传感器查看是否停止；
3. 联系技术支持。