Volvo Penta TAD1640GE Скачать руководство пользователя

Страница: 43 / 94

TWD1643GE

Exhaust Temperature (Code 1.9, PID 173/SPN 1184)

Cause

Reaction

Remedy

• Exhaust temperature to high

• Warning lamp lights up

• Engine is shutdown

• Insufficient air supply

• Low coolant level

• Air in the coolant system

• Faulty circulation pump

• Blocked charge air cooler

• High temperature, charge air-

cooler

• High back pressure in the

exhaust system

• Check wastegate function

TWD1643GE

Exhaust Temperature (Code 4.9, PID 173/SPN 1184)

Cause

Reaction

Remedy

• Short circuit to positive (+) or

negative (-)

• Open circuit

• Exhaust temperature to high

• Warning lamp lights up

• Engine control unit limits

engine power

• Check that the exhaust tem-

perature sensor connector is
properly mounted

• Check that the wiring to the

exhaust temperature sensor
is not damaged

• Check that the exhaust tem-

perature sensor is correctly
mounted

• Check the exhaust tempera-

ture sensor function

Oil Temperature Sensor (Code 3.7, PID/SPN 175)

Cause

Reaction

Remedy

• Shorted to plus (+) or minus

(-)

• Break

• None

• Check that the cable harness

to the oil temperature sensor
has not been damaged

• Check that the oil tempera-

ture sensor has been con-
nected correctly

Oil Temperature (Code 5.8, PID/SPN 175)

Cause

Reaction

Remedy

• Oil temperature is too high

• The engine control module

limits engine output(unless
protection has been turned off
with thediagnosis tool
VODIA)

• Check the oil level

• Check the oil temperature

sensor function

Fault Code Register

7748681 12-2011

Содержание TAD1640GE































































































Результаты поиска

Содержание TAD1640GE

Отзывы:

Похожие инструкции для TAD1640GE

Бренды по названию

Популярные бренды

Volvo Penta TAD1640GE, Руководство оператора

Результаты поиска

Содержание TAD1640GE

Отзывы:

Похожие инструкции для TAD1640GE

Бренды по названию

Популярные бренды