Volvo Penta TAD1640GE Скачать руководство пользователя | Manualshive

Страница: 24 / 94

background image

Starting

Make it a habit of giving the engine and engine room a visual check before starting. This will help you to discover
quickly if anything abnormal has happened, or is about to happen.
Also check that instruments and warning displays show normal values after you have started the engine.

WARNING!

Never use start spray or similar products as starting aid. Explosion risk!

Before Starting

•

Check that the oil level is between the MIN and MAX
marks.

NOTICE!

The oil level can be read both when the

engine is stopped (the STOP side of the dipstick) and
with the engine running (the OPERATING side of the
dipstick).
For filling refer to

Oil level, checking and topping up

.

•

Open the fuel valves.

•

Check the fuel pre-filter; refer to

Draining conden-

sate, fuel system page 65

•

Check that no leakage of oil, fuel or coolant is pres-
ent.

•

Check the coolant level and that the radiator is not
blocked externally. Refer to

Coolant Level, Check-

ing and Topping Up page 68

and

Cooler, External Cleaning page 70

WARNING!

Do not open the coolant filler cap when the engine
is warm, except in emergencies, this could cause
serious personal injury. Steam or hot fluid could
spray out.

•

Turn the main switch(es) on.

•

Move the engine speed control to idle, and open the
disengageable clutch/gearbox if installed.

IMPORTANT!

Never break the circuit with the main switch while the
engine is running, as this may damage the alternator.

STOP

OPERA

TING

P0004311

P0002078

22

7748681 12-2011

«
...
22
23
24
25
26
...
»

Содержание TAD1640GE































































































Отзывы:

Нет отзывов

Похожие инструкции для TAD1640GE

Бренд: BAFANG Страницы: 12

Бренд: FAAC Страницы: 28

Бренд: ULPOWER Страницы: 20

Бренд: Garmin Страницы: 14

Бренд: Navistar Страницы: 197

Бренд: Beta Marine Страницы: 88

Бренд: Stihl Страницы: 40

Бренд: MTD Страницы: 40

Бренд: Parker Страницы: 32

Бренд: Key Automation Страницы: 50

Бренд: NetGain Motors Страницы: 34

Бренд: FUTABA Страницы: 2

Бренд: Raider Страницы: 193

50-400 V CA Series

Бренд: TEM Страницы: 44

Бренд: WÜRGES Страницы: 24

Бренд: Hacker Страницы: 2

Бренд: Hacker Страницы: 7

Бренд: Hacker Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды