Volvo Penta D4-260 Скачать руководство пользователя страница 88 | Manualshive

Страница: 88 / 124

background image

Battery, Maintenance

WARNING!

Risk of fire and explosion. Never allow an open flame
or electric sparks near the battery or batteries.

WARNING!

Never confuse the positive and negative poles on the
batteries. Risk of arcing and explosion.

WARNING!

The battery electrolyte contains extremely corrosive
sulfuric acid. Protect your skin and clothes when charg-
ing or handling batteries.
Always use protective goggles and gloves. If battery
electrolyte comes into contact with unprotected skin
whas off immediately using plenty of water and soap.
If battery acid comes in contact with the eyes, flush
immediately with plenty of water and obtain medical
assistance without delay.

Connecting and disconnecting the battery

Connecting

1 Connect the + cable (red) to the + pole on the bat-

tery.

2 Connect the – cable (black) to the – pole on the

battery.

Disconnecting

1 Remove the – cable (black).

2 Remove the + cable (red).

Cleaning

Keep the batteries clean and dry. Contamination and
oxide on the batteries and battery poles can cause
stray currents, voltage drop and discharge, especially
in wet weather. Remove oxidation from the battery
poles and terminals, using a brass brush. Tighten the
terminals securely and grease them with terminal
grease or petroleum jelly.

P0002107

Maintenance

86

7748921 04-2008

«
...
86
87
88
89
90
...
»

Содержание D4-260





























































































































Отзывы:

Нет отзывов

Похожие инструкции для D4-260

Бренд: phytron Страницы: 29

Бренд: GRITAL Страницы: 4

Бренд: Perkins Страницы: 112

Бренд: Exalto Страницы: 28

GARDEN SNOWBUSTER (160F)

Бренд: Texas Страницы: 33

Бренд: Teryair Страницы: 13

Бренд: Stobag Страницы: 12

Бренд: Lycoming Страницы: 83

Бренд: Airdog Страницы: 28

Бренд: Chicago Pneumatic Страницы: 88

Бренд: DETROIT Страницы: 64

Бренд: Sanyo Denki Страницы: 20

Бренд: PYD Electrobombas Страницы: 36

Бренд: Mitsubishi Heavy Industries Страницы: 156

Бренд: Briggs & Stratton Страницы: 179

Бренд: MVVS Страницы: 6

Бренд: MVVS Страницы: 7

Бренд: O.S. engine Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды