Volvo Penta D4-260 Скачать руководство пользователя страница 86 | Manualshive

Страница: 86 / 124

background image

Electrical System

The engine is equipped with a 2-pole electrical system
and an alternator. System voltage is 12V or 24V.

WARNING!

Always stop the engine and break the current using the
main switches before working on the electrical system.
Isolate shore current to the engine block heater, bat-
tery charger or accessories mounted on the engine.

Main Switch

IMPORTANT!

Never disconnect the current with the main switches
when the engine is running, the alternator and elec-
tronics could be damaged.

The main switches must never be switched off before
the engine has stopped. If the circuit between the alter-
nator and the battery is disconnected when the engine
is running, the alternator and electronics can be dam-
aged. For the same reason the charging circuits must
never be re-connected with the engine running.

Fuses

12–volt system (engine)

The engine is fitted with automatic circuit breakers. The
circuit breakers cut the power if the system is over-
loaded.

If it is not possible to start the engine or if the instrument
stops working while running, the circuit breaker may
have been activated.
Resetting will take place automatically.

Maintenance

84

7748921 04-2008

«
...
84
85
86
87
88
...
»

Содержание D4-260





























































































































Отзывы:

Нет отзывов

Похожие инструкции для D4-260

Бренд: Fagor Страницы: 174

TSA 200-100-220

Бренд: SCHABMULLER Страницы: 56

Бренд: NOVAK Страницы: 2

ERS VAR10 SZ 2500

Бренд: Warner Страницы: 16

Бренд: ACME motori Страницы: 23

Бренд: Toyama Страницы: 44

Бренд: Nakanishi Страницы: 2

Бренд: Clinton Страницы: 7

Бренд: Honda Страницы: 15

Бренд: Honda Страницы: 60

Бренд: Barrus Страницы: 50

Бренд: Briggs & Stratton Страницы: 10

Бренд: Wood-mizer Страницы: 134

Бренд: Paccar Страницы: 111

Бренд: Briggs & Stratton Страницы: 10

Бренд: Waukesha Страницы: 140

Бренд: E-FLITE Страницы: 3

Power 25 Brushless Outrunner

Бренд: E-FLITE Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды