Volvo Penta D4-260 Скачать руководство пользователя страница 21

Страница: 21 / 124

Configuration menu

Press button 5 for five seconds to enter the

Configu-

ration menu

. Navigate with the up and down arrows,

select with the right arrow.

NOTICE!

The port engine, or both engines must have

the ignition on when display settings are made.

System information

System information shows the

EVC-menyn

and is han-

dled by the knob on the control panel. For more infor-
mation, see chapter

Instruments and Con-

trols page 20

Settings

Language

: Setting of what language the informa-

tion is to be presented in are made in the EVC-
menu, see

Instruments and Controls page 20

Bleep

: On/Off, setting if pressing the instrument

buttons will be followed by a beep or not.

Engine

: Setting of what kind of installation the dis-

play is a part of and which engine is to be shown
inthe display.

Display

: Setting of intervals (unit settings are made

in the EVC-menu, see

Instruments and Con-

trols page 20

Rpm interval, 2500–9000 rpm, in steps of 500 rpm
Speed, on/off
Speed interval, 10–100 knots, in steps of 10 knots
Graph interval, 2 min, 10 min, 30 min, 60 min, 2 h,4
h or 8 h

BACK

SETTINGS

LANGUAGE

BLEEP
ENGINE
DISPLAY

ENGLISH

OFF

PORT

P0002408

BACK

UNITS

SPEED

OIL PRESSURE
TURBO PRESSURE
FUEL RATE

DISTANCE

KM/H

kPa
kPa

L/H

P0002409

Instruments and Controls

7748921 04-2008

Содержание D4-260





























































































































Результаты поиска

Содержание D4-260

Отзывы:

Похожие инструкции для D4-260

Бренды по названию

Популярные бренды

Volvo Penta D4-260, Руководство оператора

Результаты поиска

Содержание D4-260

Отзывы:

Похожие инструкции для D4-260

Бренды по названию

Популярные бренды