Volvo Penta D4-260 Скачать руководство пользователя страница 68

Страница: 68 / 124

Every 200 hours / at least once a year, included in extended protection

Crankcase ventilation filter

Air filter insert

Fuel pre-filter and fuel fine filter

Drive belt (tension)

Compressor, oil level

Seawater pump impeller

Sacrificial anodes (charge air cooler and heat exchanger)

Corrosion protection (space between IPS-housing and clamping ring)

Engine and propulsion unit. Clean and touch up paintwork as required

I C

All hoses and pipes – Check the condition and re-tighten the hose clamps

Exhaust hose and cooling water hoses

- Check hoses / pipes, unions and hose clamps

Inspection with VODIA (Diagnostic Tool)

Every 400 hours / at least once every 12 Months, included in extended protection

Drive-unit. Oil and oil filter

Drive-unit. Function check of seawater cock

Drive-unit and transom. Corrosion protection (sacrificial anodes)

Drive-unit antifouling coating. Repair as required

Every second year

Coolant

Every 600 hours / at least every 5 years

Turbocharger, inspect / clean as required

I C

Drive-unit. Function and wear

- Propellershaft (check straightness)

- Steering

Every 1200 hours / at least every 5 years

Drive Belt

Drive belt, compressor

Compressor, oil

Heat exchanger

I C

Charge air cooler

I C

Propellershaft seal

Maintenance Schedule

7748921 04-2008

Содержание D4-260





























































































































Результаты поиска

Содержание D4-260

Отзывы:

Похожие инструкции для D4-260

Бренды по названию

Популярные бренды

Volvo Penta D4-260, Руководство оператора

Результаты поиска

Содержание D4-260

Отзывы:

Похожие инструкции для D4-260

Бренды по названию

Популярные бренды