Volvo Penta 3.0GLP-C Скачать руководство пользователя страница 123

Страница: 123 / 136

VPA 7743722 English 10-2004

119

Technical Data

Engine

8.1Gi-E, 8.1Gi-EF, 8.1GXi-D, 8.1GXi-DF

Bore and stroke. . . . . . . . . . . . . . . . . . . . 107.95 x 111.00mm (4.250 x 4.370 inches)

Cylinders (number) . . . . . . . . . . . . . . . . . 90° V-8

Displacement . . . . . . . . . . . . . . . . . . . . . 496 cubic inches (8.1 liters)

Firing order . . . . . . . . . . . . . . . . . . . . . . . 1 – 8 – 7 – 2 – 6 – 5 – 4 – 3

Full throttle operating range Gi . . . . . . . . 4200 – 4600 RPM

Full throttle operating range GXi . . . . . . . 4600 – 5000 RPM

Idle RPM (fixed) . . . . . . . . . . . . . . . . . . . 600 RPM

Fuel System

Fuel injection . . . . . . . . . . . . . . . . . . . . . . Port injection

Fuel pumps . . . . . . . . . . . . . . . . . . . . . . . Electric

Fuel filter . . . . . . . . . . . . . . . . . . . . . . . . . Volvo Penta PN 3862228

Fuel filter location . . . . . . . . . . . . . . . . . . Refer to photographs on features pages.

Fuel type . . . . . . . . . . . . . . . . . . . . . . . . . Inside the U.S.: 87 octane (AKI) unleaded gasoline

Outside the U.S.: 90 octane (RON) unleaded gasoline

Electrical System

Charging system . . . . . . . . . . . . . . . . . . . 12 volt 75 amp alternator, with internal transistorized voltage regulator

Battery size . . . . . . . . . . . . . . . . . . . . . . . 12 volt with 650 Cold Cranking Amp (CCA) rating (135 minute reserve

capacity).

Do not use a deep cycle battery as the start battery.

Starter . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 volt 1.7kW output, planetary reduction gear

Ignition System

Distributorless . . . . . . . . . . . . . . . . . . . . . Crankshaft and camshaft triggered ignition sensors.

Ignition timing . . . . . . . . . . . . . . . . . . . . . 10° BTDC, fixed, See Workshop Manual for procedure.

Spark plugs . . . . . . . . . . . . . . . . . . . . . . . Volvo Penta PN 3861326 (2 units)

Spark plug gap . . . . . . . . . . . . . . . . . . . . 1.52 mm (0.060 inches)

Spark plug installation torque . . . . . . . . . 30 N•m (22 ft. lb.)

Cooling System

Raw water pump . . . . . . . . . . . . . . . . . . . Crankshaft mounted variable volume flexible impeller pump

Recirculating pump . . . . . . . . . . . . . . . . . Fixed impeller belt driven pump on engine

Thermostat . . . . . . . . . . . . . . . . . . . . . . . 64°C (140°F) Volvo Penta PN 3587597

Gi-EF / GXi-DF . . . . . . . . . . . . . . . . . . . . Closed cooling heat exchanger mounted on engine.

Closed Cooling System Thermostat . . . . 76°C (170°F) Volvo Penta PN 3831426

Coolant Type. . . . . . . . . . . . . . . . . . . . . . Ethylene glycol. Volvo Penta PN 381081.

Oil Capacity

Engine without filter. . . . . . . . . . . . . . . . . 8 quarts (7.5 liters)

Engine with filter . . . . . . . . . . . . . . . . . . . 9 quarts (8.5 liters)

Drive unit DP-S . . . . . . . . . . . . . . . . . . . . 2.5 quarts (2.4 liters)

Oil filter . . . . . . . . . . . . . . . . . . . . . . . . . . Volvo Penta PN 835440

Oil filter location. . . . . . . . . . . . . . . . . . . . Refer to photographs on features pages.

Oil Type

Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . Volvo Penta engine oil or suitable pure synthetic oil alternative with min.

API service rating CF/SH. See

Maintenance Schedule

on page 64.

Drive unit . . . . . . . . . . . . . . . . . . . . . . . . Volvo Penta SAE 75W/90 API service GL 5 synthetic gear oil

Power steering fluid U.S.. . . . . . . . . . . . . Volvo Penta power steering fluid PN 3851039

Power steering fluid non-U.S. . . . . . . . . . ATF oil Dexron 2 PN 1161941

Oil Pressure (Minimum)

@ 1000 RPM . . . . . . . . . . . . . . . . . . . . . 5 PSI (34 kPa)

@ 2000 RPM . . . . . . . . . . . . . . . . . . . . . 10 PSI (69 kPa)

7743722 - Downloaded from www.volvopenta.com 13/05/2008 20:17:06

Содержание 3.0GLP-C









































































































































Результаты поиска

Содержание 3.0GLP-C

Отзывы:

Похожие инструкции для 3.0GLP-C

Бренды по названию

Популярные бренды

Volvo Penta 3.0GLP-C, Руководство пользователя

Результаты поиска

Содержание 3.0GLP-C

Отзывы:

Похожие инструкции для 3.0GLP-C

Бренды по названию

Популярные бренды