Volvo Penta 3.0GLP-C Скачать руководство пользователя страница 103

Страница: 103 / 136

VPA 7743722 English 10-2004

Maintenance

22865

Propeller Replacement — DP-S

Removing the DP-S Propeller

This procedure requires you to use special tool Volvo
Penta P/N 3855516.

1. Ignition switch must be OFF.

2. Make sure the remote control is in FORWARD to

lock the propeller shaft.

3. Remove the rear propeller nut (

4. Remove the rear propeller (

5. Change the remote control position to REVERSE

to lock the propeller shaft.

6. Remove the front propeller nut (

7. Remove the front propeller (

8. Wipe the propeller shaft clean. Inspect for fishing

line; remove if present.

Installing the DP-S Propeller

CAUTION! Failure to install all components
could result in loss of the propeller and dam-
age to the drive unit the next time the boat is
operated.

1. Ignition switch must be OFF.

2. Make sure the remote control is in FORWARD.

3. Coat the full length of the propeller shaft and the

inside of the propeller hub with Volvo Penta pro-
peller shaft grease P/N 828250; removal of the
propeller will be difficult if this is not done.

4. Install the front propeller (

5. Install the front propeller nut (

) and tighten it to

45 ft. lb. (60 Nm).

6. Shift the remote control into REVERSE to lock

the propeller shaft.

7. Install the rear propeller (

8. Install the rear propeller nut (

) and tighten it to

50 ft. lb. (70 Nm).

9. Shift the remote control into NEUTRAL. The pro-

peller should turn freely.

7743722 - Downloaded from www.volvopenta.com 13/05/2008 20:17:06

Содержание 3.0GLP-C









































































































































Результаты поиска

Содержание 3.0GLP-C

Отзывы:

Похожие инструкции для 3.0GLP-C

Бренды по названию

Популярные бренды

Volvo Penta 3.0GLP-C, Руководство пользователя

Результаты поиска

Содержание 3.0GLP-C

Отзывы:

Похожие инструкции для 3.0GLP-C

Бренды по названию

Популярные бренды