VOLTCRAFT DSO-2104 Скачать руководство пользователя страница 41

Страница: 41 / 66

4.Advanced User Guidebook

●Display

Push the

Utility

button, select

Function

in the right menu, select

Display

in the

left menu.
The description of

Display

Menu

is shown as the follows:

●

Adjust

Push the

Utility

button, select

Function

in the right menu, select

Adjust

in the

left menu.
The description of

Adjust

Menu

is shown as the follows:

Do Self Cal (Self-Calibration)

The  self-calibration  procedure  can  improve  the  accuracy  of  the  oscilloscope
under  the  ambient  temperature  to  the  greatest  extent.  If  the  change  of  the
ambient  temperature  is  up  to  or  exceeds  5

℃

, the self-calibration procedure

should be executed to obtain the highest level of accuracy.

Before executing the self-calibration procedure, disconnect all probes or wires

Function

Menu

Setting

Description

Function

Configure

Show the configure menu

KeyLock

Lock all keys. Unlock method: push

Trigger Menu

button in trigger control

area, then push

Force

button, repeat

times.

About

Show the version and serial number

Function Menu

Setting

Description

Function

Display

Show the display menu

BackLight

0% - 100%

Turn the

knob to adjust the backlight.

Graticule

Select the grid type

Menu Time

OFF, 5S

–

30S

Turn the

knob to set the disappear

time of menu

Function Menu

Description

Self Cal

Carry out the self-calibration procedure.

Default

Call out the factory settings.

ProbeCh.

Check whether probe attenuation is good.

Содержание DSO-2104



































































Результаты поиска

Содержание DSO-2104

Отзывы:

Похожие инструкции для DSO-2104

Бренды по названию

Популярные бренды

VOLTCRAFT DSO-2104, Руководство пользователя

Результаты поиска

Содержание DSO-2104

Отзывы:

Похожие инструкции для DSO-2104

Бренды по названию

Популярные бренды