Vollrath Cayenne Series, Руководство оператора

Страница: 3 / 36

3
ENGLISH
O
peratOr
’
s
M
anual
3. Mount the brackets and unit to a suitable surface using holes (E) and
suitable hardware.
c
enteR
m
ount
i
nstallation
Top mount brackets may be purchased as an option for direct-wired units.
The brackets are available in 1” height or 2” height. Dual units require
brackets on each unit.
NOTE:
For units longer than 72”, a minimum of three (3) mounting points
consisting of the two ends and the center of the unit must be used.
1. Access the area the unit will be mounted in and mark the location the
center mount brackets will be mounted. Make sure the material the unit
will be mounted to will support the weight of the unit.
2. The brackets must be located near the ends of the unit for greatest
stability.
3. Mount the hanging bracket (A) with the “T” slot cutout, in the locations
identified in step 1. Figure 3.
D
B
G
C
A
F
E
Figure 3. Installing Center Mount Brackets.
4. Loosen the two screws (B) located in the center of the flat channel
plates (C) far enough so they do not protrude out of the bottom of the
plate.
5. Slide the channel plates (C) into the channel (D) on the top of the unit.
6. Measure the distance from the center points of the hanging brackets
(A) and slide the channel plates (C) in the channel (D) on the top of the
unit so the center screws (E) in the channel plate (C) match the distance
between the center of the “T” slot (G) in the brackets (A).
7. Tighten the two outside screws (B) in the channel plate (C) to lock the
channel plate in position.
8. Loosen the nut (F) in the center of the channel plate (C) but DO NOT
REMOVE.
9. Raise the unit and align the nut (F) in the center of the channel plate (C)
with the “T” in the bracket (A) mounted in step 2.
10. Slide the nut (F) through the “T” slot and TIGHTEN THE NUT to keep the
unit in place. THE NUT MUST BE TIGHTENED TO PREVENT THE UNIT
FROM SLIPPING OUT OF THE BRACKET.
c
hain
m
ount
i
nstallation
NOTE: Units over 72” in length, must use the center mounting point.
1. The unit is shipped with mounting tabs (A) located on each end of
the unit. For units that are longer than 72”, three (3) mounting points
consisting of the two ends and the center of the unit must be used. See
Figure 4.
2. Loosen the screws (B) holding the mounting tabs in place but do not
remove. Rotate tabs (A) to an upright position and the attach chain to
holes (C). The chain must support each side of each end of the unit
evenly.
NOTE:
This unit must be installed in an area that will not be affected by the heat
from the unit. Damage to solid surface counter tops or other materials in
the heat zone of this product are not covered under warranty.
k
ool
-t
ouch
®
t
Rim
i
nstallation
The Kool-Touch
®
trim option is shipped separately. It will need to be installed
on the unit. We recommend that this option be installed before the unit is
mounted.
1. Beginning on the side that does not have the control box (A), slide the
Kool-Touch
®
(B) panel into position by starting at one end of the unit. Slide
the Kool-Touch
®
panel in the channel (C) on the side of the unit until it is in
place. (Ganged units will require two pieces trimmed to fit). See Figure 1.
B
A
C
Figure 1. Installation of Kool-Touch
®
Panels.
2. The side of the unit that has the control box will need to be trimmed.
Measure the area that is to be covered by the Kool-Touch
®
panel.
3. Mark the length to be covered on the Kool-Touch
®
panel.
4. Place a damp soft cloth under the end of the Kool-Touch
®
panel to be cut
to prevent the Kool-Touch
®
panel from scratching or slipping while it is
being cut.
5. Using a hacksaw with a fine metal or plastic blade, slowly cut the panel to
length.
6. Install the panel on the unit in the same manner as the opposite side.
u
nit
i
nstallation
- d
iRect
w
iRe
m
ounting
t
op
m
ount
i
nstallation
Top mount brackets may be purchased as an option for direct-wired units. The
brackets are available in 1” height or 2” height. Dual units require two sets of
brackets.
NOTE:
Top mount brackets may not be used with units longer than 72”.
1. Access the area the unit will be mounted in and mark the location the
center mount brackets will be mounted. Make sure the material the unit
will be mounted to will support the weight of the unit.
2. Secure the top mount bracket (A) to the mounting holes (B) using
lockwashers (C) and screws (D). Repeat on the other end. See Figure 2.
A
B
D
C
C
E
Figure 2. Installing Top Mount Brackets.