Voith IPC 4 Скачать руководство пользователя страница 22

Страница: 22 / 55

Voith

Turbo H + L

Hydraulic GmbH & Co. KG

25000057510-TED-ENX-04

6 Pressure fluids

This section describes the requirements for pressure fluids.
Note the other information in the general oil recommendations (doc. no. 250.006051)

Operating pump combinations with different pressure fluids is only possible in a few
exceptions. Please request further information from Voith Turbo H + L Hydraulic!

between 40°C and 60°C.

See the technical data

on page 24 ff.

HFA

(Oil/water emulsion, oil

percentage 20%)

DIN EN ISO 12922

Due to the very low

viscosity values, this

group can only be used

under certain conditions.

Yes

HFB

(Oil/water emulsion, oil

Release by Voith Turbo H + L Hydraulic is required in all cases!

Petroleum or similar

fluids

Release by Voith Turbo H + L Hydraulic is required in all cases!

Release by Voith Turbo H + L Hydraulic is required!

Ecubsol Widroflamm 5.5, 36

Nafic

Fyrguard

Other HFC fluids may be permissible upon consultation with
Voith Turbo H + L Hydraulic

Never mix different oil types or oils from different manufacturers without checking

for compatibility. We always recommend discussing any such matters with the
manufacturer or supplier.

When selecting the operating fluid viscosity, always consider the operating fluid

temperatures by adhering to the permissible viscosity values.

“No” indicates that the fluid can be used within the technical data.

“Yes” indicates that the operating data must be reduced compared to the technical
data.

Fig. 6.1: Requirements

Internal gear pumps

Pressure fluids

www.Laheghi.com

Содержание IPC 4
























































Результаты поиска

Содержание IPC 4

Отзывы:

Бренды по названию

Популярные бренды

Voith IPC 4, Руководство по эксплуатации

Результаты поиска

Содержание IPC 4

Отзывы:

Бренды по названию

Популярные бренды