Vogelsang FX116 Скачать руководство пользователя страница 40

Страница: 40 / 45

Troubleshoo ting

WBV.PU.003.EN FX116 V1.0

Possible cause

Possible measure

Observe notes and
safety notes



Chapter

aligned

manufacturer's specifications if necessary.

Belt drive slips

Tighten in accordance with manufacturer's
specifications.

Faulty electrical connector

Check electrical equipment.

"Connection to the power
supply"

Error in the hydraulic system

Check the hydraulics.

Motor speed too low during
variable frequency drive
operation

Install external fan, increase motor speed.

"Variable frequency drive
operation"

Stiff running caused by
swollen lobe elastomer

Check the medium resistance of the lobe
elastomer.

"Material description for
rotary lobes"

Stiff running caused by
accumulation of solid matter
in the gaps

Clean pump chamber, adjust drive.

"Repair", "Connection to
the power supply"

Oil level in the gearbox is not
OK



Chapter

"Gearbox"

"Maintenance"

Differential pressure too high

Reduce differential pressure.

"Specifications"

Medium viscosity above the
nominal value

Reduce speed. Increase medium temperature.

"Intended use"

Medium viscosity below the
nominal value

Increase speed, decrease medium temperature,
replace wear parts.

"Repair"

Medium temperature above
the nominal value

Reduce medium temperature.

"Intended use", "Material
description for rotary lobes"

Medium temperature below
the nominal value

Increase medium temperature (after consulting
Vogelsang).

Содержание FX116














































Результаты поиска

Содержание FX116

Отзывы:

Бренды по названию

Популярные бренды

Vogelsang FX116, Руководство по эксплуатации

Результаты поиска

Содержание FX116

Отзывы:

Бренды по названию

Популярные бренды