2
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a
qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may
cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual
and do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect
assembly, or inappropriate use.
WARNING!
ELECTRICAL SAFETY INSTRUCTIONS
THIS PRODUCT IS POWERED BY ELECTRICITY. IN ORDER TO AVOID BURNS, FIRE AND ELECTRIC SHOCK, PLEASE READ THE
FOLLOWING INSTRUCTIONS CAREFULLY.
•
DO NOT CLEAN PRODUCT WHILE POWER IS CONNECTED.
•
DO NOT DISASSEMBLE OR REPLACE COMPONENTS WHILE POWER IS CONNECTED.
•
NEVER OPERATE THE SYSTEM WITH A DAMAGED CORD OR PLUG. PLEASE CONTACT YOUR SELLER TO REPLACE
DAMAGED PARTS.
•
NEVER OPERATE SYSTEM IN DAMP ENVIRONMENTS OR IF ANY ELECTRICAL COMPONENTS HAVE MADE CONTACT
WITH LIQUIDS.
•
ALTERATIONS OF THE GIVEN POWER UNIT ARE NOT ALLOWED.
•
OUTDOOR USE IS PROHIBITED.
OPERATING INSTRUCTIONS
: When the system is powered on, the existing desktop height will appear on the
control panel.
Upward and Downward Movement
Press and hold the up or down arrow until the desk reaches the desired height.
Memory Mode
To store a certain height in the controller's memory, first press "M" (do not hold). The display will begin flashing.
Now press “1”, “2”, “3” or “4” within five seconds to store the current height in memory. Each number can store
a different height. Once in memory, you can recall any of the four height settings by pressing the corresponding
button. Touching any button will stop the automatic adjustment.
Power-Saving Mode
When no actions are made for over 2 minutes, the system will enter power-saving mode. Touch any button to
enter operating mode.
Function Mode
Press and hold the “M” button for 3 seconds, or until “S - -” begins flashing on the display. Press “M” again to
enter Function mode. Within function mode, use the up and down buttons to scroll through settings, and
use the “M” button to select options. If no action is taken for 20 seconds, the desk will return to operating
mode.
• Change Displayed Unit (Un):
Press the up or down buttons until the display shows “Un”, and press “M” to
select. Press up or down to select “SI” (metric) or “In” (imperial). Press “M” to save the setting.
• Change Brightness (br):
Press the up or down buttons until the display shows “br”, and press “M” to select.
Press up or down to select Low (L), Normal (n) or High (H) brightness. Press “M” to save the setting.
• Beeper (bEE):
Press the up or down buttons until the display shows “bEE”, and press “M” to select. Press up or
down to select “OFF” or “On”. Press “M” to save the setting.
• Collision Force Detection (CF):
Press the up or down buttons until the display shows “CF”, and press “M” to
select. Press up or down to select “OFF”, Low (L), Normal (n) or Heavy (H) collision force detection. Press
“M” to save the setting.
• Set Height Limit (SH):
Press the up or down buttons until the display shows “SH”, and press “M” to select. Press
up or down to select Original Height (O), Low (L) or High (H). Press “M” to select the adjustment setting.
-Original:
Press the up or down buttons until the displayed height matches the height of the
desk surface, then press “M” to save the setting. For accuracy, this adjustment should be made
with the desk lowered to the minimum height (60cm/23.6”). The maximum adjustment is
80cm/31.6”.
-Low:
Press the up or down buttons to set the low limit of the desk, then press “M”
to save the setting. The minimum height cannot be adjusted lower than the desk’s minimum
60cm/23.6” height.
-High:
Press the up or down buttons to set the high limit of the desk, then press “M” to save the
setting. The maximum height cannot be adjusted higher than the desk’s maximum
125cm/49.2” height.
OPERATING CONTROL PANEL
