Vitek VT-TSP8 Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 64

background image

34

2. Click “Enable” and set the alarm holding time.
3. Set alarm trigger options. The setup steps are the same as temperature measurement
settings. Please refer to temperature measurement settings chapter for details.

6.3.3 SD Card Error

When there are errors in writing to the SD card, the corresponding alarms will be triggered.
1. Go to Config

à

Alarm

à

Exception

à

SD Card Error as shown below.

2. Click “Enable” and set the alarm holding time.
3. Set alarm trigger options. Trigger alarm out, Email and FTP. The setup steps are the same
as temperature measurement settings. Please refer to temperature measurement settings
chapter for details.

6.3.4 IP Address Conflict

1. Go to Config

à

Alarm

à

Exception

à

IP Address Collision as shown below.

2. Click “Enable alarm” and set the alarm holding time.
3. Trigger alarm out. When the IP address of the camera is in conflict with the IP address of
other devices, the system will trigger the alarm out.

«
...
37
38
39
40
41
...
»

Содержание VT-TSP8

































































Отзывы:

Нет отзывов

Похожие инструкции для VT-TSP8

Бренд: Zavio Страницы: 16

GigE Vision STC-CMB2MPOE

Бренд: Omron Страницы: 55

M.Zuiko Digital ED 150-400mm F4.5 TC1.25x IS...

Бренд: Olympus Страницы: 202

Бренд: Xcellon Страницы: 16

Бренд: Zee Страницы: 14

Бренд: 70mai Страницы: 52

NVIP-1DN3020V/IR-1P

Бренд: Novus Страницы: 40

Бренд: Safety Track Страницы: 13

Бренд: Gator Страницы: 24

Бренд: Polaroid Страницы: 9

Бренд: Medion Страницы: 12

ZX-5N - SLR Camera - 35mm

Бренд: Pentax Страницы: 102

Бренд: Vantrue Страницы: 43

Бренд: Adaptive Recognition Страницы: 29

Бренд: Dukane Страницы: 30

Бренд: JVC Страницы: 2

Бренд: Honeywell Страницы: 2

DS1-MP10RX series

Бренд: NEC Страницы: 204

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды