Vitek VT-TSP8 Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 64

background image

39

Long Polling Port

: The port is used for a persistent connection of third-party platform to push

smart data, like face pictures.

6.4.3 Server Configuration

This function is mainly used for connecting network video management system.

1. Check “Enable”.
2. Check the IP address and port of the transfer media server in the ECMS/NVMS. Then
enable the auto report in the ECMS/NVMS when adding a new device. Next, enter the
remaining information of the device in the ECMS/NVMS. After that, the system will
automatically allot a device ID. Please check it in the ECMS/NVMS.
3. Enter the above-mentioned server address, server port and device ID in the corresponding
boxes. Click the “Save” button to save the settings.

6.4.4 DDNS

If the camera is set up with a DHCP connection, DDNS should be set for the internet.
1. Go to Config

à

Network

à

DDNS.

2. Apply for a domain name. Take www.dvrdyndns.com for example.
Enter www.dvrdydns.com in the IE address bar to visit its website. Then Click the “Registration”
button.

«
...
42
43
44
45
46
...
»

Содержание VT-TSP8

































































Отзывы:

Нет отзывов

Похожие инструкции для VT-TSP8

Бренд: Uniden Страницы: 140

Neo smartpen N2

Бренд: Neolab Страницы: 6

Бренд: iDeaPLAY Страницы: 14

Бренд: HIKVISION Страницы: 17

Бренд: Voyager Страницы: 2

Бренд: KaiCong Страницы: 44

Бренд: FujiFilm Страницы: 134

Бренд: Axxera Страницы: 2

Бренд: Intevac Страницы: 30

Бренд: TytoCare Страницы: 76

Бренд: G-Lenz Security Страницы: 14

Бренд: Polaroid Страницы: 1

Бренд: Dalsa Страницы: 90

Бренд: Nixplay Страницы: 22

Contaflex Super B

Бренд: ZEISS IKON Страницы: 12

Бренд: iGuard Страницы: 2

Бренд: L-Tron Страницы: 2

R800 - Professional Presenter Presentation Remote Control

Бренд: Logitech Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды